Jump to content
SAU Community

Recommended Posts

Hey guy,

I have just put my thermo fan in the car but i haven’t yet hooked it up to the power. Has anyone else put one in a r32?

My poor little bnr32 seized up the clutch fan. :D

I want to know if i should just hook it up to a switch in the cabin or not?(manual turn on and off)

Regards Keith

Link to comment
https://www.sau.com.au/forums/topic/210153-thermo-fans/
Share on other sites

I've got two switches hooked up on mine. One to the ignition, the other is a thermo switch (turns on when it reaches a certain temp). Each fan runs one relay.

I've got two thermo fans, 1x shrouded 14inch fan, and 1x 12inch fan unshrouded (no space due to aircon).

Wiring would be the same between any car.

Link to comment
https://www.sau.com.au/forums/topic/210153-thermo-fans/#findComment-3717346
Share on other sites

I use a 14" thermo with the standard shroud, its controlled by an electronic thermo switch that reads from the standard sensor in the thermostat housing...

Ive never had over heating issues since I started using this set up, I have the switch set to 84 degrees and even on a hot day it doesnt go over 91 maximum.

The best thing about removing the engine fan is the increase in engine response, by taking off the standard fan you reduce parasitic drag on the engine by quite a lot which makes it much easier to rev.

Link to comment
https://www.sau.com.au/forums/topic/210153-thermo-fans/#findComment-3720084
Share on other sites

  • 1 month later...

Have fitted plenty of these to GTRs and GTSTs. The main thing is to make sure that the radiator is a twin core one as the late version gtst had single core and don't seem to work efficiently with thermo's.

As for wiring, the best way is to use a thermo switch to control them. These can be as simple as a probe that sits underneath your radiator hose or a fan switch that is tapped into your manifold or a adaptor in your hose.

I usually go for the first as it is easiest, but have used both with good results.

Do not rely on manual switches as there will come a day when you will forget.

As for wiring it you will need either two relays or the one i use is a 70amp one that you can run both thermos from(much easier and less wiring)

Here is a brief description of how it wires in.

The thermo switch turns the relay on by giving it a earth when it reaches it preset temp and the relay then turns on both thermo fans.

Put the thermos behind the radiator in between the radiator and engine as they cause an airflow restriction when they are in front. You can use two 12" which are actually 13" in total diameter and these will fit perfectly or you can run 2 13" by overhanging them and blocking the sides in so they can only suck through the core.

Make sure you stagger them so that one thermo sits to the top and one sits to the bottom of the radiator, and also make sure they are wired and fans are spinning the right way to pull air instead of pushing air.

If you need a diagram drawn i would be happy to or i can show you how i do it as i am doing one for a customer at the moment.

Link to comment
https://www.sau.com.au/forums/topic/210153-thermo-fans/#findComment-3806394
Share on other sites

Ok this might sound a bit dodge, but talked with my local auto electrician, and he's a bit of a lateral thinker (does good work) He said I should be able to use EA to BF at least thermo fans? As they all had them from then on? Or commodore ones, just need to measure up the radiator and compare the sizes. He did say commodores had larger thermo fans. Anyone know anything about using falcon or commodore ones? Or should I steer clear of them?

Link to comment
https://www.sau.com.au/forums/topic/210153-thermo-fans/#findComment-3816751
Share on other sites

Ok this might sound a bit dodge, but talked with my local auto electrician, and he's a bit of a lateral thinker (does good work) He said I should be able to use EA to BF at least thermo fans? As they all had them from then on? Or commodore ones, just need to measure up the radiator and compare the sizes. He did say commodores had larger thermo fans. Anyone know anything about using falcon or commodore ones? Or should I steer clear of them?

Member on here with Candy red 32 with 26/30 swears by the EA thermo fans, personally im looking at the flex-a-lite thermos which are a twin thermo in a single casing.

Link to comment
https://www.sau.com.au/forums/topic/210153-thermo-fans/#findComment-3816776
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...