Jump to content
SAU Community

Recommended Posts

I had a quick look at doing that when I was going to buy an R33

and it didn't look too difficult. I think to do it properly the battery might need to be moved over a bit and you could replace the front boot-trim with a carpeted MDF panel with the sub-box behind it. You would need a hatch in it to access the battery. You could also flush mount an amp behind it.

In my R32 which is similar but without the battery I'm making a sub-box that mounts onto the metal panel that seperates the boot from the backseat. The 10" sub mounts through the panel and fires through the armrest hole in the back seat.

This type of setup won't go very loud because you don't get the benefit of bass-loading the same way you do if you fire the sub backwards into the boot but it is good for a sound quality system.

I see no reason why it wouldn't work in a 33 but if you want bang for your buck a single 12" facing backwards would be easy.

Thnks guys,

I have 2 10 inch pioneer free air subs at the moment left over from a project a year or so ago. As i dont need an extremely loud system i was thinking of just installing one of these subs facing backwards out of the battery compartment. Didnt want to move anything at this stage (or construct boxes).

Anyway thanks for the input.

Gary

  • 4 weeks later...

i built a sub box for my 33 that fits into the area thats free next to the battery and fuses and potrudes out off the rear tunnel about 130mm and finishes off and can still fit a hsv bag in the boot with no hassles if you need photos email me at [email protected]

I'm looking at getting a 10" subbie and using this space for the placement...

i had a 12 inch pioneer in my 33 in a box facing left to right of the boot, it kicked ass man...if you put it in the battery area it wont sound as good, poor sound qualities and obstructions.

Could you install a divider wall to shield the battery / electrics from the sub? You'll get less obstruction this way

If you're handy with fibreglass you can easily mount a small sub next to the battery. We do it all the time with Skylines and Soarers.

As for effecting sound, your subwoofer should be crossed over quite low (around 100hz). At this frequency the sound will not be noticealbiy effected at all. Remember the front speakers are the ones that have the important task of creating and reproducing the 'body' of the music. The subs simply fill out the lower end of thre sound spectrum. :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...