Jump to content
SAU Community

Nos

HTMR32

By HTMR32,
in Victoria

 Share

Recommended Posts

DogKnight Mentor

DogKnight

Posted
Posted

Im guessing if you had an empty bottle in your boot not connected to anything that would be fine. The second you have NOS in the bottle or any buttons/switches fake or not, youre most likely going to be in trouble.

I doubt they could even do you if the bottle was full as long as there is no system in place for the car to use it. Otherwise you would need a permit to transport it?

Link to comment
https://www.sau.com.au/forums/topic/210656-nos/page/2/#findComment-3726041
Share on other sites
htial Grand Master

htial

Posted
Posted

I remember reading something about this in AutoSalon or Street Machine...

It was something along the lines of it is fine to have it installed... ...and a full bottle in the car... ...As long as it takes a good bit of work to get the bottle hooked up... ...and just as long as you're not driving on the road with it hooked up you'll be fine...

I also asked my local police contact and he said you'd be, and I quote, "A f$%&ing try hard wanna be that would get a defect from the first rookie ass kisser trying to get in with their SS(Senior Sergeant)"...

I'd say put it in a trailer queen or a track car... ...and just keep it off the street...

Link to comment
https://www.sau.com.au/forums/topic/210656-nos/page/2/#findComment-3726981
Share on other sites
gadget1382 Enthusiast

gadget1382

Posted
Posted
Any of you two got proof for what you typed there? Last official documentation I read agrees with Al in that you cannot have ANY part of a NOS system connected to a road rego'd car.

I do not have documented proof, but asking for curiosity sake a TMU police officer and a NOS supplier in victoria and them both saying the same thing is enough for me.

Link to comment
https://www.sau.com.au/forums/topic/210656-nos/page/2/#findComment-3728081
Share on other sites
some_cs_student Veteran

some_cs_student

Posted
Posted
I do not have documented proof, but asking for curiosity sake a TMU police officer and a NOS supplier in victoria and them both saying the same thing is enough for me.

I would definitely get a second-opinion from the police officer, it sounds incorrect.

And if I were a NOS supplier, of course I'd tell you it was legal, I'd want to sell NOS :)

Link to comment
https://www.sau.com.au/forums/topic/210656-nos/page/2/#findComment-3729779
Share on other sites
BRUNSKIGTST Proficient

BRUNSKIGTST

Posted
Posted

lol stop provoking the young fella, or being stupid and saying you can have this or that when you officially know nothin and you actually know you cant have the bottle. just dont believe those guys they want to see you make a thread one day saying you got a fine for haveing this this and this in ur car and all they want to do is laugh at you just dont do it or get one you just wasteing ur time and money on stupid things which give all of use skyline drivers a bad name to the cops, anyone agree?

Link to comment
https://www.sau.com.au/forums/topic/210656-nos/page/2/#findComment-3730601
Share on other sites
R33GTST4Door Enthusiast

R33GTST4Door

Posted
Posted (edited)

when the police impounded my car they had a look over my car. he said he was just having a look and isnt doing a roadworthy inspection, when he was doing so he said if he seen any part of a nos setup my car, he would put it off the road.

Edited by R33GTST4Door
Link to comment
https://www.sau.com.au/forums/topic/210656-nos/page/2/#findComment-3730679
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...