Jump to content
SAU Community

Recommended Posts

I am not sure about Ethanol. Some say that it is actually good for the car (small amounts) and some say that you don't need it and can be harmful to engine.

Does BP have ethanol in their petrol? I know Shell advertise that it doesn't contain any ethanol.

Way back before the dawn of time (I.E. Before SAU started and we were all in SDU) someone took the inititive to test all 3 fuels and in terms of the RON ratings they were all pretty close with no major winner between the 3 of them. BP was first, then Mobil 8000 then Optimax. All over the 98 RON mark.

What was more interesting was the chemical content within the fuels. I can't remember what contained what but Optimax had other additives and stuff. I think it was supposed to be a bad thing but don't quote me on that.

I've since tried to find the thread but it's gone to Thread Heaven... :P

However I feel that you should stick with what you think. All 3 aren't bad and it's not like your going to gain massive HP by running [insert fuel brand here]. People have had different experiences with all fuels some run better on this, others on that.

I use whatever I'm closest to when I need to fill up, but generally have gone for Optimax. Ive found through the 3 main ones that Ultimate seems to give me good fuel economy, where Mobil gives me good performance and Optimax is a combination. Like a good all-rounder... I have noticed that results on Optimax tend to vary from servo to servo sometimes, but if you find a good one stick with it.

Man BP Ultimate is pretty hard to find in my area!!

Drove into 2 BPs and one had premium unleaded and the other just had unleaded. Look like a fool driving in and driving off haha. I think I found one for sure now with BP Ultimate, but still haven't try it out yet.

i tryed bp and vortex and my car didnt like em at all

ive been told by many that these are the best and have highest octane etc

but for sum reason my line didnt take to it very well

ran much better with optimax

:confused:

I manage a caltex servo on the Gold Coast and it has the worst premium grade fuel I have used :D I never use Caltex Vortex it doesnt have the RON of the other brands... You can tell by the difference in price between the unleaded. Vortex is generally 5 cents dearer than unleaded at Caltex, BP ultimate is generally 8-10 cents dearer !!! I only run ultimate where possible, If I cant I use Optimax.... These two give better mileage which offset the extra cost.. Never really liked Mobile after all the deal with the aviation fuel getting diluted in our petrol so I havnt tried them! The other good thing to do is run Nulon petrol treatment.. by far the best. Its a red container.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...