Jump to content
SAU Community

Mods Pls Delete

gtrzilla
 Share

Recommended Posts

br3ndan Mentor

br3ndan

Posted
Posted

i dun think u would of damaged the diff from jacking it up there.

I jack from their whenever im doing work on the rear end.

Besdies i think thats where you meant to jack it.. as i cant recall anywhere else u can...

Unless you got a hoist.

Link to comment
https://www.sau.com.au/forums/topic/212527-mods-pls-delete/#findComment-3754998
Share on other sites
(OO)SKYLINE(OO) Grand Master

(OO)SKYLINE(OO)

Posted
Posted
seems to be more noticeable after jacking it up

or do gtr diffs just sound like this :worship:

Oh BTW Orion, get a Rear Wheel Alignment done.

Cuz you have change the rear suspension, its put the geometry out of whack and needs to be done cuz its 4WD.

But I don't think that will help with the whirring noise. Or it might...

But when you jacked it up at the diff, I don't think you would have crushed or bent anything in the diff...

Anyway get ya mechanic to check it out.

My diff made a similar noise when rolling and while driving. Sounded like a Wwhhoooo noise. So I got it reconditioned.

Link to comment
https://www.sau.com.au/forums/topic/212527-mods-pls-delete/#findComment-3756471
Share on other sites
(OO)SKYLINE(OO) Grand Master

(OO)SKYLINE(OO)

Posted
Posted

I still got the receipt for my rear diff

About $1380, thats recondition, installed ready to drive and it was not as much as I thought too.

But get it check out 1st.

I did it at Le Mans Automotive in Templestowe.

Link to comment
https://www.sau.com.au/forums/topic/212527-mods-pls-delete/#findComment-3757776
Share on other sites
GTS4WD Grand Master

GTS4WD

Posted
Posted

You would of snapped a cooling fin before doing internal damage to the diff..

Not form the jacking.

Sure your not just Paranoid?.. Happens to me too..

Whirring diffs seem to be common threads in this section.

Just seems like their noisy from factory.

Best advise is change the diff oil.. see the condition its in and put a higher quality product in. See how that goes..

People jump to recondition diffs/'boxes too quicky.

For that price you may aswell buy an after market LSD.

Link to comment
https://www.sau.com.au/forums/topic/212527-mods-pls-delete/#findComment-3761475
Share on other sites
vinnie32GTS4 Mentor

vinnie32GTS4

Posted
Posted
ill have to get them to check the diff oil then on my next service

but i just had a major major service and replaced all fluids, and if anything the diff whirr is louder!

what diff oil did u use???

Link to comment
https://www.sau.com.au/forums/topic/212527-mods-pls-delete/#findComment-3763886
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
    • MBS206
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By MBS206 · Posted

      That's some really horrible design with the way it's cut/shaped! Is there much damage to the box that failed in? IE, new fork and you can go again, or is it a total rebuild again? Id be trying to build that piece from scratch, and getting some reliefs added in the corner to hopefully stop breakage, and then swapping boxes ASAP, and then doing the same to the currently good working box. I'm assuming hard shifts have not been friendly to it!
×
×
  • Create New...