Jump to content
SAU Community

Recommended Posts

Item: HKS Hiper D R34 Coil over

Age: Unknown, it came with my car when bought

Condition: Unknown, it came with my car when bought

Price: AUD $499+

To Fit: (What car) R34 GTT or R33 GTR

Location: Adelaide

Contact: Can contact me via Ebay or PM me.

Comments: If interested please go to the Ebay link as it is currently on Ebay. Open to offer though

For more info please go to : Ebay Link: HKS Hiper D R34 Coil overs

post-48266-1206790224_thumb.jpgpost-48266-1206790231_thumb.jpgpost-48266-1206790260_thumb.jpgpost-48266-1206790252_thumb.jpgpost-48266-1206790244_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/212581-hks-hiper-d-r34-coil-overs/
Share on other sites

Hi,

Sorry, I dont have pic of the car when these were on it. But when I asked my suspension dealer to put in the new one (Tein SS). I asked him to set the exactly same height as when the HKS was in there. Because I liked it the most, good look/handling and able to go through speed bumps and drive way no problem.

I should be able to give you a photo of my car with the Tein SS since it will be the same height as the HKS one sometime tomorrow morning since it is dark already.

I roughly measured it and it was about 330mm Front and 335mm rear. (from centre of wheel to guard). (Although if you want a more exact measurement, let me know)

Edited by hulk

The HKS one is definitely very sharp and precise in handling. Kinda like in a go kart, gives you great feel of the road compare to the Tein SS Jap spec. However, it is quite firm and it is suited much better on tracks than the Tein SS. I been driving my car everyday for 2-3 months with those no problem, kinda got used to it. But the passengers I take find them fairly bumpy.

The Tein SS is also very good on the road, but it lacks the go kart feel and thrills of the HKS one. However, as I am driving this car everyday to work along a crappy and bumpy road in SA's northern suburb, I think the Tein SS is much more suitable for me.

Hi, These are the pictures I just took in the morning.

Hopefully will give people how it looks in the car.

Sorry, I dont really want to seperate it, so it will sell as a set of 4.

Also I think shipping to Melbourne will be around $60 - $100. (not sure, just guessing) Since it is relatively heavy. But if you can PM me the postcode I can give you a more accurate quote.

post-48266-1206831627_thumb.jpgpost-48266-1206831620_thumb.jpgpost-48266-1206833398_thumb.jpg

post-48266-1206833404_thumb.jpg

Edited by hulk

I havent adjust the height of the car, since I liked the height personally and it does the job going through speed bumps and drive ways. I dont know if these coilovers are height adjustable or not.

Edit: I searched the net regarding the HKS coilovers and found that it should be height adjustable. But I do not have the tools for it. So i guess you will have to take it to a workshop that do HKS coils to get them to set up the height.

Edited by hulk

I've got some PMs regarding the condition of the coilovers.

So I guess, I just post it here for an update.

My 1999 R34 GTT has done 40,000 km. So I am assuming the previous owner swapped it out around 20,000 km. Then the coilover should be around 15k-20k.

They dont seem to be that old, and still in reasonable condition.

Hi,

For people that Pm'ed me enquiring shipping costs.

I just had a quick quote for the following locations:

Sydney metro= about $55

Melbourne metro= about $45

Perth metro = about $70

Brisbane metro = $55

Those are registered shipping, but not insured.

Insurance would be about $10-15 on top of the price.

Help that give people a better idea of the shipping costs.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...