Jump to content
SAU Community

Recommended Posts

yes they are definately the same as something common in aus (and not the same as skyline, they are smaller)

nissan had them on the shelf when i needed them

part number is 43222-50J00

what do you mean smaller duncan. i belive most nissan's are m12x1.25 pitch do you mean shorter?

if thats the case pehaps skyline ones would be better with some after market wheels? might stop them stripping (mine stripped two on the rear right i blame shoty tyre shops and wheel spacers)

Edited by petrolfix

no they are still m12x1.25. they have a smaller diameter and length where they go through the hub. definately not as strong as the skyline ones I have broken 2 as well.

but yes if you have spacers you really should run longer wheel studs. Once you know what car they match eg pulsar you will probably be able to find aftermarket longer ones. there are standard and long aftermarket ones for skylines out there.

  • 1 year later...
yes they are definately the same as something common in aus (and not the same as skyline, they are smaller)

nissan had them on the shelf when i needed them

part number is 43222-50J00

Does anyone know if this is the same part no. for an S2.

yes they are definately the same as something common in aus (and not the same as skyline, they are smaller)

nissan had them on the shelf when i needed them

part number is 43222-50J00

can anyone confirm that S2 studs are the same part no.?

  • 3 weeks later...

Compatibility with common vehicles in Aus follows:

The 50J00 part is common across R32/33/34, RS13/S14, Z32, U13 & A31

The 28B10 part is common across R33/34

Duncan, it's interesting that you state that the 50J00 part is different to the Skyline - FAST shows them as relevant from the lowliest RB20E powered cars right up to, & including the GT-R...

Yeah good call I just checked it in FAST and saw the same GTR32 and stagea are same part # front and rear. Maybe I was just trying to fit front vs rear studs.

So the rear is common between stageas and skylines, and the front is shared with a whole heap of other stuff including u13 pulsar. good work with fast btw I've got no idea how to pull up the other models that use the same part, that would be very handy.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...