Jump to content
SAU Community

Recommended Posts

yeah champ its the wiring that needs checked...... its more than likely whats called an "earth whine" which just means that the earth wire needs some attention.... but it wouldnt hurt to get all the wiring checked out as i have had some pretty big systems in my time and i know how annoying an earth whine and other engine sounds can be when u want ur system to sound crystal clear...... what brand of sub and amps are u running in there champ???? if ur interested in some clarion subs and amps pm me and ill send ya some pics and details of my gear..... its all basically brand new.... i have had the system for a while but have recently replaced the subs with new items of the same model purely becuz im a perfectionist lolz or if u wanna grab my msn off my profile and we can chat there about what u should do with the wiring situation

Cheers for the comments guys, but I can't take credit for it, I bought it with the stereo in it. The amps are Blitz, 1x1000w and 1x5000 which I'm pretty sure are cheap ebay items? And the subs are Sony 15" explod 3000w in custom boxes which he didn't line with any dampers, so that's a job for this weelend. Thanks for the offer of amps etc, but will stick with what I've got for a bit. Getting married next year (yeah I know,lol) so no $'s for luxury items at the moment. That's why I bought the skyline. last chance before I don't have 100% say in where my dollars go.

Thanks for the help too, will have a look over the whole wiring and see what I can find.

Skyline on!!!!

:rant:

post-48987-1207114711_thumb.jpg

Dude, have u tried to put in an inline filter which cancels the engine noise coming through your speakers? Goto jaycar or an audio specialist and they will provide you with a filter. Fixed all my mates problems when i got him the filter. Aint that hard to install aswell.

MR_XTC

Howdy,

cool, it already has a filter on it. So will check all the connections etc on the weekend. Hopefuuly that will fix it. Am just turning it up loud till then so I can't hear it,lol...

Cheers

post-48987-1207168668_thumb.jpg

Is this different to alternator whine?

I found this but I don't know who wrote it, someone on the internet:

"As mentioned earlier, I found a harness that runs in that bay-area, and behind the AC unit that has MASSIVE electrical interference. I could hold the rca's near it, and the whine was louder than the music (at mid-levels).

If you can't test it that way, then grab a 3.5mm stereo mini jack (same as your earphones) to RCA boot, and use the ipod plugged into them, so you're nowhere near the body.

If that is still noisy, change your RCA cable... use a short one to test with the ipod to the amp. Grab one out of your TV/DVD player and test with it. If the noise is still there, try and borrow a friends amp, and retest all of the above.

Turn your gains down on the amp. Put a massive earth on the battery.

OR use a Ground Loop Isolator from autobarn etc.

"

This article also talks about alternator whine:

http://www.skylinesaustralia.com/forums/Ca...dio-t94069.html

But your problem may be different....

EDIT: re-read your problem, it doesn't sound like alternator whine....but I don't know that much about car audio.

dude u need to ground the muthaf*#ka up

i had it b4 and made me crazy

the filter works a little bit but makes the quality shit

(reduces bass)

bcoz u runing sum high power gear

i sugest u double ground your equipment,

even add anotha ground coming from the batterie

should fix the problem

^^ english my friend - speak it?

go to your local audio store grab a ground loop isolator. it is a patch for the problem but in you case will be easy to implement.

  • 2 weeks later...
Is your power cable running up the same side as any of your RCA's? Having RCA's too close to power cable will cause this noise..

That's most likely the problem. Exactly what happened to me :thumbsup: But the RCA's going down one side of the car, and the power cable to the amp on the other.

Howdy,

I think they are, the guy who I bought it off put in the stereo and I don't think he was all there. Unfortunately I've been flat out with work for the last 2 weeks and haven't had a chance to dig too deep into this problem. I'm going to try and get onto it this weekend. Thanks for all the help, it's been invaluable. This site rocks!

Cheers to all!

post-48987-1208381922_thumb.jpg

hi, i had the same problem in my pulsar, i added all the off the shelf filters and stuff and it still was there, i tracked it down eventually to poor rca leads, which was the last thing i thought it could be but it turned out that the rca leads that came with the wiring kit were not properly shielded, that is the shield did nothing, it is supposed to connect from one device to another, i went out and bought a high quality set of rca leads and that ultimately fixed the problem. BEWARE OF DODGY RCA LEADS, EVEN IF THEY LOOK COOL.

The best investment any car enthusiest can make is a good quality multimeter, like from altronix or jaycar, mine cost me 10 bucks but potentially saved me hundreds by not having to take the car to a auto elec.

another thing you can try is getting a ferrite core from dick smith or jaycar etc and completing as many turns as possible of the speaker wire around it, this will eliminate most RF interference by not passing it into the speaker cable but allowing audio frequencies to pass.

dave.

When teh car is on ACC you dont here it but wen teh engine is on it starts to happen am I right?

I think you might have to connect RCA wires from the headunit to the amp. Similar problem I had but mine sounded like the turbo coming from my speakers?

I have a similar problem, but mine's caused by the grounding from the battery to the Chassis to the engine block.

I ran 4 guage power from the battery to the amps in the boot, ran speaker wires down the other side of the car, did all the rules, but got the noise.

When I placed another 4 guage wire on the negative of the battery, and to the chassis, the noise vanished straight away, so something to check before ripping all your stereo gear out is the basics, lift the bonnet, have a look at the negative wire, especially in the R32's, as mine's only slightly bigger than an 8 guage earth, completely inefficient for anything more than a stock headunit.

B.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...