Jump to content
SAU Community

Recommended Posts

i had that same problem with my RB25DET mate.....my problem was that my Harmonic key was rooted....it was advancing and retarding timming as i was driving it.....and my revs were doing that as well....it would jump up and down rapidly on idle......so might be worth checking that....i had to replace my motor...goodluck

My R33 was sluggish and i had the cam angle sensor turned left (counter-clockwise) and it increased response and power (10rwkw extra). Did it on a dyno- best way because you can measure the changes to the power curve. Turning yours right might've made it worse.

It's something else you've missed i reckon. A smic swap (i've done the R34 one too) shouldn't do anything other than allow more charge to flow through the intake.

Edited by R338OY

yeah i had the r34 cooler in... then i swapped back to the stock smic cuz this stupid problem.. which i cant figure out what to do...

when i turned the cam angle sensor as far clock-wise as possible it made more power and even more drive ability but its still nothing like it used to...

engine has around 90,xxx kays on it..

only has a pod and turbo to tip zorst..

changed plugs for brand newies around 1000 kays ago..

do oil and iflter every 4000 kays,,

suck a f**king annoyhing thing..

i dont understand whats the go with this ecu diagnostic shit..

their is a tiny red and green led light on the actuall ecu.. they flash and shit when i turn that small screw all the way clock wise o the ecu..

the cat temp sensor light in the dash flashes on and off..

i dont know how to decifer them fault codes and that... what to count and all that :S

im shit i know

haha

cheeeeers

search the forum for ECU+CODES

there was a thread with what each light flash meant.

also, I'm thinking that if all this started with the SMIC install, are you absolutely certain the the 2 rubber joiners for the cooler are not cracked.

have you removed both off the car, cleaned them and thoroughly inspected them?

remember that those rubber joiners have probably not been touched for about 15 years and perhaps as you removed the stock cooler (the pipe has a lip on it) it may have cracked the rubber a little or enough to cause a leak.

it's free so might be worth checking.

i just wrote don how many times them leds flashed and that

i got

2 slow flashes

3 fast flashes

4 fast flashes

5 fast flashes

1 slow flash

2 fast flashes

?? dont know what the shit that means

and also while im waiting for a reply for the ecu codes i checked all cooler piping.. even on the throttle body.. both for the cooler every connector i could see.. their all clearlly old. but no cracks inside or out....

and also while im waiting for a reply for the ecu codes

mate seriously.

search.

I just typed in ECU+CODES just like I told you to do...

and look what happens..

http://www.skylinesaustralia.com/forums/se...2BR32+ECU+CODES

Now look at the 6th thread down.

Now look at the 3rd post.

surely you could have done this yourself.

Edited by GTST
  • 2 weeks later...

haha yeah rb20 slug.

took it to a local work shop but they could not find a thing wrong with it... no ecu fault codes showed up...

well when i was playing with it in my driveway it turned out to be the plug for my cam angle sensor was rooted and my timing belt was possibly put back on wrong as if i tried to back the timing off anywhere away from as far advanced as it would go the car would start doing the eratic idle....

i have just brought brand new gates racing timing belt and have rb25 turbo and greddy front mount to go on soonish along with a speedlab ecu remap..

cheeers for all your help guys :)

yeow

yes.. its a fair clean ceffy.. i wouldnt mind eventusally dropping in a rb25... but its a matter of cash like everything else. haha

make the rb20 boogy a bit first.. have fun with it will i got it

cheers guys

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...