Jump to content
SAU Community

Recommended Posts

hi all, im very new to this forum, i have tried to find an answer to my question but searching

but i couldnt find and threads in relation to it so im just gonna ask it again,

My R33 has recently started to surge, and want to cut out just as the turbo is spooling up,

and sometimes while i am just driving at the one speed, but is worse while accelerating..but only does it

when the engine is warmed up, never does it when it cold.

the best way to describe it is, it feels like its running outta fuel (yes there is fuel in there!)

could it be the igniter packs?

any help would be much appreciated,

great forum by the way!

cheers, craig

Link to comment
https://www.sau.com.au/forums/topic/214337-rb25-surging/
Share on other sites

I have this problem after I fitted a electronic boost controller and turn the gain or boost level up. But when I turn the boost level or gain down the problem always goes away. Sometimes with diffrent fuels the problem would come back so I had to change boost / gain levels depending on the fuel. Fo you have a boost controller fitted?

Link to comment
https://www.sau.com.au/forums/topic/214337-rb25-surging/#findComment-3785564
Share on other sites

if it sounds like its popping its probarly the coils

but if it making all the right sounds but going no where then takes off like a bat outta hell

it will be the normal r33 flat spot

most people change the ecu and have it tuned to fix the problem

but there are other ways around this problem it just depends who you speak to

Link to comment
https://www.sau.com.au/forums/topic/214337-rb25-surging/#findComment-3785608
Share on other sites

Are you running standard boost? If yes then it's not the boost cut.

My advice:

Do a search on-

O2 Sensor/oxygen sensor. Yours might be dirty/dying

AFM. It might need a clean

Spark plugs. Change them

Coilpacks. Wrap them in tape/silicone

Fuel pump. Maybe yours is on the way out. Change the fuel filter too, it's a good idea anyway.

If the problem remains after all those then get professional help. Or a psychiatrist.

Edited by R338OY
Link to comment
https://www.sau.com.au/forums/topic/214337-rb25-surging/#findComment-3785641
Share on other sites

as far as i know, the turbo has been a flowed, but seems to now be running less than the standard 7 psi, i only have a manual boost controller under the bonnet, ill change as much as i can, coils, spark plugs leads etc, if it keeps happening, ill just have to take it to morpowa, or boostin oz to get them to figure it out...thanks guys

Link to comment
https://www.sau.com.au/forums/topic/214337-rb25-surging/#findComment-3785708
Share on other sites

ok, i took the coil pack cover off, gave it a thrash to make the engine hot, it didnt do it, except for when i first started driving (when it was cold)

i got home , turned the lights off to check for a sparks fromk coils, and there was nothing.

i bought some new ngk laser platinum spark plugs that will be going in tomorrow.

could this problem possibly be my AFM?

Link to comment
https://www.sau.com.au/forums/topic/214337-rb25-surging/#findComment-3789011
Share on other sites

ah ok.. 2 of my friend's r33 had the same problems too

put it on the dyno and check the fuel pressure, might be your fuel pump

may also be fuel pressure reg too, though not very likely. i'd check fuel pump first

coilpack and afm are other possibilities, but if afm's cleaned like i've mentioned in the other post it should be fine

if afm is playing up or dirty your car wont idle properly in most cases

Edited by chiksluvit
Link to comment
https://www.sau.com.au/forums/topic/214337-rb25-surging/#findComment-3789139
Share on other sites

ok, i spent some time under the bonnet yesterday, changed spark plugs (ngk laser platinum) cleaned afm thoroughly and checked/cleaned igniter packs, also wrapped them in electrical tape just in case,

all seems good, no more surging or choking, but this typical r33 flat spot you all spaeak of is now obviuose, doesnt do it all the time, but every now and then when i boost it hard. for now, it doesnt really bother me, it still eats most ls1's so thats all im worried about at the moment ; )

i also took out the bleeder valve beacause it wasnt always hitting the 11-12 pound it usually does, instead it was only reaching 5-7 pound.

it didnt seem to make much difference without the bleeder valve, but does it matter if i leave it out?

Link to comment
https://www.sau.com.au/forums/topic/214337-rb25-surging/#findComment-3791059
Share on other sites

taking the bleed vavle out definatly wont hurt anything

the flat spot though i know how to fix it without changing the standard ecu

i have done it to my car and many others and has worked everytime

ok...how?

Link to comment
https://www.sau.com.au/forums/topic/214337-rb25-surging/#findComment-3791145
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
    • Hi @Chupapy i had several leaks from coolant pipes being corroded, i also had one leak on back of the head onto transmission. For me that leak was from the turbo water line. Follow the line to the back of the head The hose and metal pipe had perished these are the best pics I took of it at the time
×
×
  • Create New...