Jump to content
SAU Community

Recommended Posts

R32 GTS25 would be the way to go, should handle quite well.

there is a r32 with a na rb25 conversion for sale at the moment are there many of them?i currently have a Nissan pulsar n14 sr20 how will it go against that? also how much do the r32s weight and are they lsd? is there a page somewhere that has all the features

The r32 gts25 was a production car from the factory they weigh high 1300kg i think. cant help you with the lsd or how they go against n14. in my opinion r32 would be quicker.

http://www.skylinesdownunder.com/index.php...0&Itemid=97

that might help

I remeber reading somewhere that N15 SSS's will have the jump on NA R33's but the Skyline will catch up a little down the line..

Quick rundown.

Short answer: R32 - No. NA 2L is poo.. if you can find one with a 2.5L thats not too bad..

If your going to get an NA skyline.. get a 33 or 34..

Down sides..

Small brakes..

Open diffs..

4 stud wheel pattern

Slap a set of coilovers and strut bars and they handle awesomly..

My NA 2.5L R32 GTS4 can keep up with higher powered cars through the twisties without too much hassle.. but you really need to keep the engine revving to get the most out of it. It is possible to have a quick NA through the twisties with the right mods.

If you want a good good handling NA your looking at the wrong place..

NA cars are all about being light weight with awesome handling..

Have a look at:

MX5

AE86

RX7 SII

perhaps an s13

Just a thought..

I remeber reading somewhere that N15 SSS's will have the jump on NA R33's but the Skyline will catch up a little down the line..

Quick rundown.

Short answer: R32 - No. NA 2L is poo.. if you can find one with a 2.5L thats not too bad..

If your going to get an NA skyline.. get a 33 or 34..

Down sides..

Small brakes..

Open diffs..

4 stud wheel pattern

Slap a set of coilovers and strut bars and they handle awesomly..

My NA 2.5L R32 GTS4 can keep up with higher powered cars through the twisties without too much hassle.. but you really need to keep the engine revving to get the most out of it. It is possible to have a quick NA through the twisties with the right mods.

If you want a good good handling NA your looking at the wrong place..

NA cars are all about being light weight with awesome handling..

Have a look at:

MX5

AE86

RX7 SII

perhaps an s13

Just a thought..

could i also suggest a non turbo supra and non turbo 300zx, both these cars will make over 130kw at the wheels, and only weight about 1400kg's give or take

thanx for all the advice and info

id really like a r32 gts25 but im also looking at mr2 sprinta and 300zx im looking for a car that looks nice and goes good for na and drifts can any one giv me some advise on thoes cars or any other cars

R32 GTS25 is my pick, doesnt have VVT which does make a nice topend difference though. Ideally if you can pick up an R32 GTS25 that has already had the very easy to do 3l bottom end conversion, then you can achieve 150rwkw+ with the right mods.

R33 and R34 if you can get a good one for cheap then why not... But ultimately, I wouldnt spend too much on an N/A as a P plater cos you'll eventually get onto the turbo bandwagon later, save the dosh for a turbo car then :D

Z32s are a nice bus, not a fan of the big veee-six however, and no where near as easy to work on if you are inclined that way.

thanx for all the advice and info

id really like a r32 gts25 but im also looking at mr2 sprinta and 300zx im looking for a car that looks nice and goes good for na and drifts can any one giv me some advise on thoes cars or any other cars

If you want to hang your arse out.. dont go for MR2.. incredibly hard to drift.

Again.. if you want to drift, you want the lightst car possible, Sprinter. There are a couple of 4AGE converted ones already and they are a blast to drive!

I see where your comming from with an R32 as a drift car but the NA's have too many down points (in my opinion) to bother with.. no time. Im pretty sure that the NA's have a weaker box too.. and thats something you dont want in adrift car.

How about a KE70?.. It would need work.. but they are quite cheap..

MA70 (is that the right code?) Supra?

Toyota Cressida?

Ghetto Spec R31 boro drift car?

i had a look at a 300zx last nite,drove nice but yes big and heavy,sprinters are sik but there bit old,r32gts25 would be awsome if i could find one wat about r33? they any good i dont really like the look but i could settle for one,ye i read about mr2s being hard 2 drift because of the heavy rear end

  • 2 months later...
  • 1 month later...

If you really want to skid it and not just a passing fancy, jump on the Aus spec R31 bandwagon and don't look back. S13 front sus, locked diff and away you go.

If you want something thats actually nice but still cheap, I'd go NA 33 and if you are cashed, NA Supra.

If you want something NA and fast, get a V8 falcon or commy. Big cam, good free flowing exhaust, some head work and either a big carby or a good EFI system and it should be quick enough to give you a scare or 2.

  • 1 month later...

Hey Mate,

Don't know if you have bought your car yet, but i got an R32 GTS 2.0L, and i have to say it's great.

There are some small downsides though

Small engine capacity means you need to keep the revs up for any decent power.

As for drift yeah a LSD would be nice but hard to source, but great in the wet ;)

handeling: as i only have a standard one at the moment i can only go by a standard setup, which is a fair bit of fun but could be a bit stiffer.

Hope this has helped you a bit..

By the way expect to pay a fair bit nowdays as P platers are only alowed non turbo ones, so they are in high demand..

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...