Jump to content
SAU Community

Recommended Posts

Hey all,

I'm interested in learning more about suspension setup, doing my own alignments etc. Just wondering what experience people here have with any suspension literature? Basically looking for an all in one book to teach me the ins and outs of setting up my track car, as well as my road car.

Has anyone read this?: http://www.pitstop.net.au/view/technical-c...query/plu/1734/

Cheers

Dane

Link to comment
https://www.sau.com.au/forums/topic/215743-suspension-literature/
Share on other sites

The problem is that most books fall into two categories.

1. Too basic.

2. Too mathematical.

The one you have is probably the former, but add to the fact that it is horribly out of date also.

If you want a recommendation some of Carroll Smiths stuff is ok (But similarly dated). Try either of these:

http://www.amazon.com/Tune-Win-Carroll-Smi...9845&sr=1-2

http://www.amazon.com/Drive-Win-Essential-...9871&sr=1-4

If you want to risk an aneurysm go with Millikens tome:

http://www.amazon.com/Race-Car-Vehicle-Dyn...d_sim_b_title_4

Remember thought, the key to it is as much about understanding tyre behaviour as understanding chassis behaviour.

Edited by djr81

The problem is most books don't spend enough time on the implications of changing the geometry on various types of suspension. eg you wont find things such as don't lower a car with a McPherson strut front end to the point that the LCA is horizontal or inclined upwards.

This sort of thing can sometimes be useful:

http://www.racingaspirations.com/suspensiongeometry.php

The ones I refer to most in my library;

Tune to Win - Carrol Smith

Drive to Win - Carrol Smith

Saloon Car Race Preparation - Nigel MacKnight

Performance Handling - Don Alexander

Competition Car Suspension - Allan Staniforth

Race Car Engineering & Mechanics - Paul Van Valkenburgh

I have found that there is no one book that covers it, the ones that may on the surface appear to be out of date still have lots of relevance and even the heavily scientific ones have some basic stuff that anyone can grasp even if you ultimately ignore the formulas.

Cheers

Gary

Thanks fo rthe tips all, I'll have a flick through some of them and work out which is best for what I'm looking for.

The Carroll Smith books seem to have a good rep, so that might be the go. I think it will still be relevant for the type of info I'm chasing.

Cheers

Dane

Performance Handling by Don Alexander is quite a helpful one, not too complex, not too simple. A fair amount of stuff in there on tuning with tyre temps, which I thought was pretty handy, although I'm not sure how handy it would be in real life as it's not often you come into the pits hot.

Milliken's probably a bit much for what you want, is mostly for design and endless calculations rather than anything incredibly helpful for tuning. Tyres, Suspension and Hanlding by Dixon is much the same thing.

Have you had a look at my thread?

http://www.skylinesaustralia.com/forums/Su...ic-t161623.html

Might find something useful in there... Maybe...

Oh, and this guy writes articles for Racecar Engineering, lot of PDFs there, decent amount of theory, and a fair bit of practical stuff too. Just found it the other night, been reading heaps :)

http://rejsa.nu/forum/viewtopic.php?t=40875

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...