Jump to content
SAU Community

Help Please ! - Lh Tie Rod End Needed

exitSTAGEAright
 Share

Recommended Posts

bernardshorty Community Regular

bernardshorty

Posted
Posted
Hi Guys,

needing some help with a part for my series 1 stagea.

LH Tie rod end.

Any ideas ?? The auto shop is looking at a skyline one but unsure if it will fit until try.

Stu

hey bud i got one gen nissan tie rod end which i bought still in box if ya want it $100 cost me 140. just have no use for it as i got mine rebuilt as there was only one gen one in australia and i needed 2. cheers bernard.

exitSTAGEAright Enthusiast

exitSTAGEAright

Posted
  • Author
Posted

cheers everyone, looks like the skyline part they ordered will be OK. Find out tomorrow i guess :(

$100 retail from Nissan, I will put the part number up once I get it in case anyone needs to know.

  • 9 months later...
Stagstock Community Regular

Stagstock

Posted
Posted
buy aftermarket

its only like 40.00 more for a pair

The R33 tie rod ends are half the size of the stagea end, they have nearly 10mm play in the housing on the hub... most definately not a SAFE replacement.

chook Mentor

chook

Posted
Posted

3 different tie rods outers for Stageas, depending on model, year, 4wd/2wd, MT/AT etc

48520-0cu25(2wd)

48520-15u25(4wd)

48520-23u25(4wd)

2 different for R33, both are same part # as 2 of the 3 Stagea tie rods.

48520-15u25(2wd)

48520-23u25(4wd)

best to ensure you are getting right part for your car. pm me your vin and ill let you know.

66yostagea Grand Master

66yostagea

Posted
Posted

I am not 100% but think the correct one is an R34 GTR. I went through this a couple of years ago. It was the fourth one I got from the wreckers that was correct.

From memory the first one was for a smaller dia tie rod. The second was the correct dia, but the threaded section was too long. I cut it shorter but then discovered the thread depth was now too shallow. The third was the correct dia and length but the taper was too small.

Fourth time correct. The length from the center of the taper pin to the end of the threaded section is approx 90mm.

It was a sod of an experience. And verx exxy, as with allthe running around I chopped out two tyres.

BKC34 Collaborator

BKC34

Posted
Posted

well i've ordered the 33gtr tie rod, hopefully its right, my reasoning behind it was that the 33gtr/gtst/ stagea all have the same chassis, so i figured the steering and suspension would be similar, anyways ill find out next week when it gets here

also interesting to note that extension housing seal is the same as 32/33 rwd's and also subaru 4wd's

  • 11 months later...
xyster Newbie

xyster

Posted
Posted

how did you go? i have a S2 stagea and I ordered the R33gtr tie rod from bursons.. went to install it to find the threaded part far too short to fit the nut and split pin back on.

well i've ordered the 33gtr tie rod, hopefully its right, my reasoning behind it was that the 33gtr/gtst/ stagea all have the same chassis, so i figured the steering and suspension would be similar, anyways ill find out next week when it gets here

also interesting to note that extension housing seal is the same as 32/33 rwd's and also subaru 4wd's

66yostagea Grand Master

66yostagea

Posted
Posted
how did you go? i have a S2 stagea and I ordered the R33gtr tie rod from bursons.. went to install it to find the threaded part far too short to fit the nut and split pin back on.

Look at my previous post, it gives all the pitfalls.

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Cas issue

      By GTSBoy · Posted

      The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Duncan
      RB26DETT Sketchy boost mod?

      By Duncan · Posted

      Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • nash47
      Cas issue

      By nash47 · Posted

      Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • nxh
      R34 4 door side skirt identification

      By nxh · Posted

      Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
×
×
  • Create New...