Jump to content
SAU Community

Recommended Posts

NO!!

they are good for popping airbags. think there are 8 or so on these so I would only use a meter in them. if it is a LED one then that is a different story. still prefer a meter.

jon,

I'm bored so I'm tearing yours to bits.

Dammit! I'll leave it to you then. I can't wait to hear the result....

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

NO!!

they are good for popping airbags. think there are 8 or so on these so I would only use a meter in them. if it is a LED one then that is a different story. still prefer a meter.

jon,

I'm bored so I'm tearing yours to bits.

Cool...hope you find more cool stuff! The G35 guys keep on talking about their remotes ability to wind down all four windows by just pressing the unlock button 3 times and holding it...I tried but no dice...

partial PDF from the 05/06 service manual.

that is relevant to what we are talking about.

its missing a relay so the whole concept of adding a switch is a myth. there is more to it that that. I would say: fuses,relays, switches,seats.

I'll know more over the next day or so.

jon,

you may want to stay away for a few days whilst I find this missing relay :)

g35sedan_heatedseat.pdf

Ok my 04 coupe is a 70th and has the seat warmers,

you can push the switches up or down, what is the difference ?

up is for high heat, down is for low

as in the thicker and longer bar for up, and thinner and shorter bar down low

can you do us a favour and open you console and take a pic of where the wires go form the switches?

its as simple as

- pull down the plastic around the bottom of the shifter

- pop out the pin

- lift off the gearknob

- lift up the armrest

- then lift the console from where the switches are

this takes about 2-3mins and requires no screwdriver or anything

i would just like to see on a coupe where the wires go after they coem out of the switches

thanks mate!

Warren

warren,

easier way.

remove covers on seat bolts. remove 4x14mm bolts position seat so it lays back out of the way:(DO NOT DISCONNECT IT!)

look at 4 pin white plug in middle of seat. it has 2 wires: a heavy red and black in it for the seat power ONLY. IF it has 4 wires going THROUGH the plug into the seat itself then you have heated seats.

based on the 05/06 sedan passenger seat you will have a LT GRN/BLK & GRY/BLU in that plug from teh car side - those will match with the ones in the centre console

the car (in the case of the 05/06 sedan I have here) is set up for them its a case of swapping seats, adding switches and finding the relay and fuse for it.

jon,

yours is wired for it but thats it.

Edited by Chris Rogers
  • 2 weeks later...

just to update this..

i have found a company that sells carbon fibre heating elements

http://www.heatedseatkits.com/index.html

costs $180 for the pair for front seats

they are OEM items in many cars in the USA..

and i've also recieved my heated seat switches from the G35 :)

so once my exams are over, my plan is to find out if i have the heating elements or not, and if i don't i'm going to look at getting a set of heating elements and wiring them up using the stock switches to control it

it should suit those cold summer mornings just fine!

haven't checked as yet..

i'm studying for exams which are on friday which means i can procrastinate all day on the computer and be guilt free (as my notes are open in an adjacent window), but if i leave the vicinity of my computer/books (ie to go to the car) i get massive guilt about not studying..

i know i'm weird

i will check for the wiring before i think about getting any elements though

Just noticed my car has rectangular marks where the heated seats buttons should be. Seems to be a lump there on both sides of the console. Does anyone else have this? Looks kinda dodgey.

yes I have these too.

Unless the vehicle is equiped with heated seats there will be covers in place of the switches. So 99% of 35's will have these covers.

on some of them the covers are knockouts. in the case of warrens car they are visible but not punched.

warren,

re: question - yes.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • A 1.5 way is a 2 way. It is just a 2 way with a less aggressive ramp on overrun.
    • The ABS and/or TCS being missing/broken will not cause the engine to misbehave. It just casues CEL to come on and annoy you. The CEL is useless if it is always on, so you have to do the things you have to do to get rid of it, so it can be useful. Being a Stag ECU, then yes, it will not expect TCS to be present. But it will expect ABS to be present and working. You will need to either make the ABS CU talk to the ECU (don't ask me what that will take on an NA R34), and make sure the hardware is working....or, you just need to blank it out in Nistune. Do not persist with the stock ECU. You will just have problems. Gte it Nistuned. Start from there. DO YOU HAVE A BOOST SENSOR? The ECU's boost sensor that it. It is connected to the loom at the rear of the coil cover. Usually rides on the firewall on an R34, but is usually bolted down to a bracket along with all the other crap at the back of the coil cover when a Neo is dropped into another car. If you do not have it, the ECU will shit the bed. So, do you have one?
    • So sadly the fuel pump etc was not it. The pump and filter is new and it is still cutting around 4000 rpm. A read something about ABS/TCS (engine is from stagea and ECU too so no TCS) and i dont know for 100% that my car has ABS. It has ABS "cube" in engine bay but i dont think it works(or at least from my braking experience). Can be something like that?  I will be driving the car next week to Nistune tuner to properly see what is wrong...  
    • the Tomei LSD fluid with lsd kit. frustrated that it was shaking the car to crap and affecting everything else negatively, I pulled the diff last night, and removed the lsd carrier, could not find anything wrong, however it seem to be 100 locked up acceleration, and deacceleration, wondering if they sent me a 2 way not a 1.5??  either way I installed the stock open carrier back in place. test drove everything smooth as butter again. no shake, shutter, random, what felt like clutch slip and grab or drive shaft play, etc. something differently wrong in side the lsd. I might bother taking it apart (if possible) to figure out what's going on inside this carrier, as bought too long ago to return.  only draw back is its back to a one wheel wonder.
×
×
  • Create New...