Jump to content
SAU Community

Recommended Posts

Hey guys

i have tried looking, but i cant find any clear answers to how to remove the rear seat in R33 GTST

I need to re install stock springs for a RWC and i have done this in my GTR 32 but that did not require rear seat removal

Can someone PLEASE

tell me how to remove the rear seat/parcel shelf, so i can remove the rear shocks/springs

thanks heaps

Link to comment
https://www.sau.com.au/forums/topic/217702-removing-the-rear-seat-r33/
Share on other sites

Two bolts (one each side) at the bottom of the rear seat. Undo them, pull the seat (bottom half) up and it will dislodge from two tight plugs (may require a big jolt to pull them out). Pull that out of the way.

Two or three bolts holding the top half of the seat down the bottom where you have removed the other part of the seat. Undo them and pull it up out. Parcel shelf you carefully pull out (dont forget to unplug speakers). I dont think there is any bolts from memory just plugs that pop out.

Its very simple but just make sure you have un-done all bolts before trying to pop the plugs.

Two bolts (one each side) at the bottom of the rear seat. Undo them, pull the seat (bottom half) up and it will dislodge from two tight plugs (may require a big jolt to pull them out). Pull that out of the way.

Two or three bolts holding the top half of the seat down the bottom where you have removed the other part of the seat. Undo them and pull it up out. Parcel shelf you carefully pull out (dont forget to unplug speakers). I dont think there is any bolts from memory just plugs that pop out.

Its very simple but just make sure you have un-done all bolts before trying to pop the plugs.

the first two bolts,

are they accessed from the boot or "under" the seat in the back

the only reason i ask is i dont have the car here and i want to suss this out so on the w/e when i get it i know exactly what to do

cheers

hey mate,these pics shud pritty much explain it all for you. the 2nd picture with the 2 half circles is about where the other 2 bolts are that hold the rear part of the seat in.the bolts are easy to get out but the clips on the bottom half of the seat will probly get you! i find it alot easier to use a very long screw driver as a lever inbetween the seat and the floor.

Jack

post-38410-1209994361_thumb.jpg

post-38410-1209994453_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...