Jump to content
SAU Community

Recommended Posts

Guest Robo's

This is the first car i have had with severe oversteer. I want to reduce it!!

Its got Tein NR suspension, rides very firm, i feel this maybe the cause. Also 17*9 at the rears with 255/40/17 which mean it should hang on, but it doesnt, any good throttle will send the rear out, i might try reducing the back tyre pressures to reduce it.

Anyone elses opinion.

Link to comment
https://www.sau.com.au/forums/topic/21783-r33-oversteer/
Share on other sites

you only reduce ur tyre pressure if you, say driving a 4WD on a sandy beach so your tyre didn't sink.

Or, you go to drag race and need a little tyre wall flex so you get more grip on hard (straight) launch, not just bumping around the track.

For anything else, pump up your tyres with enough pressure in it, coz they're good for corner handling and less rolling resistance will save fuel.

Link to comment
https://www.sau.com.au/forums/topic/21783-r33-oversteer/#findComment-462741
Share on other sites

youll need to do some more research. My konis are adjustable, but you have to remove the shock, fully compress it, and rotate the rod to adjust the damping, there are no external adjusters so they dont LOOK adjustable.

Maybe have a look at your rear camber, and make sure there is no rear toe out as previously suggested. Might have excessive rear camber.

I would even take it to a suspension specialist, get them to look at all the suspension mods and alignment, then drive the car, and work from there.

Link to comment
https://www.sau.com.au/forums/topic/21783-r33-oversteer/#findComment-463585
Share on other sites

I've got the whiteline kit with adjustable sway bars, front on hard and the rear in the middle. still find that on fast tight corners (eg turning right at lights at around 60, no traffic around!) it has a tendency to understeer just a little, but then to flip into oversteer without much/any warning. can be rather scary and hard to correct, to the point that i have a little less confidence in the car's handling than i feel i should. the rear end is far less "twitchy" than a lot of rwd cars i have driven, but the way it can just snap out on you with no warning worries me.

Question, i guess, is should i try full soft at the rear sway? the shocks are bilstein all round but not adjustable

Link to comment
https://www.sau.com.au/forums/topic/21783-r33-oversteer/#findComment-478845
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
×
×
  • Create New...