Jump to content
SAU Community

Recommended Posts

Guest Robo's

This is the first car i have had with severe oversteer. I want to reduce it!!

Its got Tein NR suspension, rides very firm, i feel this maybe the cause. Also 17*9 at the rears with 255/40/17 which mean it should hang on, but it doesnt, any good throttle will send the rear out, i might try reducing the back tyre pressures to reduce it.

Anyone elses opinion.

Link to comment
https://www.sau.com.au/forums/topic/21783-r33-oversteer/
Share on other sites

you only reduce ur tyre pressure if you, say driving a 4WD on a sandy beach so your tyre didn't sink.

Or, you go to drag race and need a little tyre wall flex so you get more grip on hard (straight) launch, not just bumping around the track.

For anything else, pump up your tyres with enough pressure in it, coz they're good for corner handling and less rolling resistance will save fuel.

Link to comment
https://www.sau.com.au/forums/topic/21783-r33-oversteer/#findComment-462741
Share on other sites

youll need to do some more research. My konis are adjustable, but you have to remove the shock, fully compress it, and rotate the rod to adjust the damping, there are no external adjusters so they dont LOOK adjustable.

Maybe have a look at your rear camber, and make sure there is no rear toe out as previously suggested. Might have excessive rear camber.

I would even take it to a suspension specialist, get them to look at all the suspension mods and alignment, then drive the car, and work from there.

Link to comment
https://www.sau.com.au/forums/topic/21783-r33-oversteer/#findComment-463585
Share on other sites

I've got the whiteline kit with adjustable sway bars, front on hard and the rear in the middle. still find that on fast tight corners (eg turning right at lights at around 60, no traffic around!) it has a tendency to understeer just a little, but then to flip into oversteer without much/any warning. can be rather scary and hard to correct, to the point that i have a little less confidence in the car's handling than i feel i should. the rear end is far less "twitchy" than a lot of rwd cars i have driven, but the way it can just snap out on you with no warning worries me.

Question, i guess, is should i try full soft at the rear sway? the shocks are bilstein all round but not adjustable

Link to comment
https://www.sau.com.au/forums/topic/21783-r33-oversteer/#findComment-478845
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What Duncan said sounds right. Also, it looks like they only have the driver's mat. Not the rest. Because looking at the diagram: KG4911 is just the mat for the driver. KG4900 is the full set if I'm not mistaken and discontinued.   But, it looks like they may still have the full set for the manual S2. Might be worth checking for the other models as well as they seem slightly different. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/misc/G49 Man, I'm tempted.
    • I dunno about that as a blanket statement. Pitwork is Nissan's "Nissan genuine" thing, and for stuff like timing belts, I have found them to be excellent. Of course, for things like oil filters, you always use proper trusted brands anyway, not whatever the OEM has taken to using.
    • Ahhhh... If you were putting 12V to the led in there, that's likely made it very unhappy. Chances are how you put power, was 12V across an LED that's meant to only have about 20mA through it at peak, and a forward voltage of about 1.8 to 2.4 volts. That circuit is likely only a 3V3 circuit, and will have a resistor in series with the led too. That's my guesstimate on that light, without having touched one.
    • Another vote for installing them and see how you go.  I mean, you already own them, why would you not fit them? 
    • I have had too many of those over the years, my cars have a toolkit or at minimum a cheapy multi tool thing because its too easy to be snookered by some stupid plastic clip that stops you checking the battery terminal isn't loose.
×
×
  • Create New...