Jump to content
SAU Community

Recommended Posts

Hey Guys

Just wondering who has done this and if you have do you have any pics you could possibly post up.

Im thinking about doing it to make it a shoe in for my new wheels at the front.

If anyone can help me it would be appreciated.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/218286-32-gtst-with-gtr-front-gaurds/
Share on other sites

mate its simple as unbolting ur old gaurds and take them off, then bolting the new gtr ones on

the only thing u will have to change is the inner gaurd plastic, so make sure you have a gtr one first.

there is no complication to this at all, and if you know where all the bolts are located to remove the original gaurd your fine

and if you dont know where they are take your time and take the bolts you can see out first then try and move it and see where there is still a bolt or where it isnt moving and take it easy and you will get it.

to help you there are 5 or so bolts in the engine bay, 2 in the door area and one behind the indicator, and some in around the wheel arch. and u will need to move the side skirt to get to one or two aswell

i think thats it but yeh take ur time and you wil learn along the way.

pm me if you want pics on where the bolts are located.

Hey Guys

Just wondering who has done this and if you have do you have any pics you could possibly post up.

Im thinking about doing it to make it a shoe in for my new wheels at the front.

If anyone can help me it would be appreciated.

Thanks

4dr on Ns.com

http://www.nissansilvia.com/forums/index.p...howtopic=293446

Rear guards are done as well which kinda defeats what im asking for... I need/want pics of 32's with GTR fronts and stock rear guards.

But thanks for the link though!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...