Jump to content
SAU Community

Recommended Posts

Well... if you want to get technical, it runs a two stage boost. First 5 psi and then up to 7psi at higher revs. You can earth the one wire and make it 7 psi all the time though. This is the same for the R33. R32's run 10 psi.

Just to clarify, I'm talking about GTT's, GTSt's here... not GTR's

Link to comment
https://www.sau.com.au/forums/topic/218768-r34-question/#findComment-3860135
Share on other sites

Found it, R34 GTT Stock boost is 7psi, just under 0.5 bar.

R34 GTR is same as 32/33 GTR... which is what Topaz was referring to I believe.

Wow, I really thought the GTT's were 11psi like the 32GTR's. 7psi is shit! :P

Not sure what 33GTR's are stock, 34GTR's are 1bar stock.............................. I'm 95% sure

Edited by Topaz
Link to comment
https://www.sau.com.au/forums/topic/218768-r34-question/#findComment-3861541
Share on other sites

Well... if you want to get technical, it runs a two stage boost. First 5 psi and then up to 7psi at higher revs. You can earth the one wire and make it 7 psi all the time though. This is the same for the R33. R32's run 10 psi.

That changes when you get the RB20 actuator yeah??

10 psi??? :P

You're doing that to your car aye??

Link to comment
https://www.sau.com.au/forums/topic/218768-r34-question/#findComment-3861829
Share on other sites

i am running 0.85 bar(12 psi) daily.... izit bad then?? lol

12 psi will be fine, but you may want to check that its not leaning out at all. Upgrading your fuel pump is always a good idea when running more boost. Probably wouldn't go too much higher than that until you have some other bits and pieces to support it.

That changes when you get the RB20 actuator yeah??

10 psi??? :)

You're doing that to your car aye??

Yep thats right :D Cause the R32's are 2 litres, they run 10 psi to make up for the smaller capacity. By changing to the RB20 wastegate actuator, you are getting 10 psi instead of 7 psi. This is a lot better than a boost controller as there is no chance of boost spikes, therefore safer for your turbo. You still need to ground that one wire to get rid of the two stage boost, and then bypass the solenoid. There is a tutorial somewhere here on SAU :)

Link to comment
https://www.sau.com.au/forums/topic/218768-r34-question/#findComment-3862342
Share on other sites

Yep thats right :P Cause the R32's are 2 litres, they run 10 psi to make up for the smaller capacity. By changing to the RB20 wastegate actuator, you are getting 10 psi instead of 7 psi. This is a lot better than a boost controller as there is no chance of boost spikes, therefore safer for your turbo. You still need to ground that one wire to get rid of the two stage boost, and then bypass the solenoid. There is a tutorial somewhere here on SAU ;)

Link??

So with the actuator you don't need a boost controller??

Edited by Marco-R34GTT
Link to comment
https://www.sau.com.au/forums/topic/218768-r34-question/#findComment-3862622
Share on other sites

Here you go Mark ;)

clicky

With the actuator you don't need a boost controller. This is how it works

First, ground the one wire mentioned in the tutorial. This will change it to constant high boost mode meaning istead of a two stage boost of 5 psi then 7 psi above 4500 rpm, you are running 7 psi all the time.

If you put the RB20 wastegate actuator in and bypass the solinoid, you now have 10 psi all the time. You have to bypass the solinoid cause it will limit you to 7 psi. The solinoid is what is used to create the two stage boost. Since you are not running a two stage boost anymore, you don't need it :P

Edited by NISZILA
Link to comment
https://www.sau.com.au/forums/topic/218768-r34-question/#findComment-3862674
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • oh they were with that motor, you need to remove the engine to change the spark plugs (don't have to, but it does make it easier)
    • I certainly fall into the annoyed camp, but glad to hear that if it's happening at low boost then I'm not likely going to blow a turbo and end up with metal shards in my oil. Just feels like it prevents me from really driving it without hesitation and "peak" performance. Wonder if it's the VCAM, it did an impressive job of shifting the torque curve and faster spool, but maybe now it's "too fast" and there's too much air for how open the throttle is.  Based on some other threads, will also do some reading on synchronizing the actuators. They are the default actuators that come on the Garrett's and I would think they would be set the same coming from the factory, but if the turbos don't actually work exactly the same way at the same time as previously mentioned, it would be worth making sure the actuators are actuating together properly
    • I went down this rabbit hole before, ended up sourcing a motor from the UK (I'm in Japan) which also didn't function correctly. With the original motor, I disassembled it and reassembled it and it works somewhat, sometimes. What I could deduce from all my screwing around is that there is calibration of the gears on the inside of the motor and two ramps on the main gear which activate switches that operate the motor and move the sunroof either to retract into the roof or tilt. Where I got stuck was that, it seemed in my case that one or both of the switches that are activated by the ramp on the gear did not always activate and thus the motor did not move, causing it to sometimes not retract or tilt (apologies, I've forgotten which way it didn't work.).  Of course this part is discontinued at Nissan now, it's the same part in the S15 but no other models. I also contacted the manufacturer of the component for schematics - forgot the name, they're based in Gifu - but they declined to share the information due to being bound by an NDA, sadly. Looking through my pictures now, it seems I last had a crack at this in 2022. See, I so kindly wrote "open" and "close" next to the switches. If you figure it out, please do tell me. Those little switches, with the red buttons may need to be replaced.
    • It says 300ZX, does that make it an Aus delivered car? Funny how back in the day I just couldn't care less about Z32's and these days I am just in love with them. Back when Nissan was into pushing the envelope. 🤣
×
×
  • Create New...