Jump to content
SAU Community

Recommended Posts

Hey,

Decided to sell some of my bits and pieces I have lying around that I no longer really need, and due to GTR repairs I could use a little extra cash.

All items located in Canberra, ACT.

Blitz BOV set (suited for BNR32)

Age: Unknown

Condition: 2nd hand, but have give both the pipe and BOVs a good clean. Both are functional.

Price: $200 posted

To fit: BNR32 GTR

Comments: Includes the gaskets, bolts, BOV pipe aswell as the BOVs themselves.

DSC00422.jpg

DSC00423.jpg

DSC00426.jpg

Exhaust Cannon, Used

Age:Unknown

Condition:Used, has been cut off from prevous car, but can still be welded again as there is sufficent pipe

Price:$50 posted

To fit:Came off a S13, but should fit any standard exhaust.

Comments: As said it came off a S13, and it appears to be a Trust exhaust end, but whether the prev owner of the car it came off just put in on??

DSC00432.jpg

DSC00434.jpg

Exhaust Cannon, New

Age:Brand new still in box(minus photo taking)

Condition:New, have used andonising spray to paint end andonised blue but can be removed with striper if not wanted.

Price:$65 posted

To Fit: Generic Autobahn brand

Comments: Generic brand from Autobahn, is new but has tip painted.

DSC00429.jpg

Light detector for Cefiro's automatic headlights

Age:Unknown

Condition:S/H, Clips are broken off so it cannot be mounted in factory harness.

Price:$20 posted

To fit: Cefrio or Skyline with automatic headlight setting.

Comments: Was going to convert my GTR to have auto headlights, but gave up.

DSC00431.jpg

Please PM me if interested.

Cheers!

Paul

Link to comment
https://www.sau.com.au/forums/topic/219463-r32-gtr-parts-and-other-bits/
Share on other sites

Hey mate,

Whats the sound like on the BoVs, and do they cause any idling issues / flat spots at all?

Cheers

Andrew

Hi Andrew,

They are louder from what i remember, but as for flat spots i do not know as I only had them on a week then took them off for registration and didnt put them back on as the Stock ones will suit my needs for now.

Cheers

Still trying to sell all the parts above (including the BOVs)

PM me if you actaully want to buy them and can within 48 hours. I'm trying to sell these asap to pay for parts i need, and don't really want to wait another week.

These will fit both R32 GTR and r33 GTR, as it is a direct replacement for the stock BOVs

Thanks!

Price Drop!

BOVs: $180 posted

Exhaust cannons: $40 for either posted

Ceffy Light sensor: $10 posted

Breather filter thing: $Free if you know what it can be used for.

THANKS!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...