Jump to content
SAU Community

Recommended Posts

Gday everyone, this is my 1st post.

im seriously thinking of getting a R33 GTR.

What would be needed to get the car into the 11-10's 1/4mile ?

I have a very lame knowedge of skylines and have been a holden fan. Currently owning a VXSS tricked up and it runs a 12.2 on streets. but being 22 i need more. i want to see 11 to 10's and its getting time to sell the VXSS.

How much money would need to be spend on the GTR to see 11's ?

and whats a good imported R33 GT-R worth ? im guessing around 45?

any help would be AWSOME !!

thanks

MELV

Link to comment
https://www.sau.com.au/forums/topic/22066-help-getting-a-gtr-r33-into-10s/
Share on other sites

  • Replies 56
  • Created
  • Last Reply

Top Posters In This Topic

A guy on this forum has a R33 gtr running ~10.4sec 1/4 miles

Name is Leewah, give him a PM and ask about the cost. My guess is about another $25-30k after purchasing the car. This would be a quality job that is still drivable

the r33 gtst that they use is up for sale for $40 000 something i think which seems like a lot cheaper way to do it to me, they also said that the car is capable of alot more but there not touching it cause its for sale its 400hp at the wheels its suppost to be the fast 2.5 in the country at the time

if you dont get much out of them try tony rigolies work shop i dont know where they are but the deal with some serious cars and they have a shop in sydney and on the goldy they have an r33 gtst that there trying to get 600hp at the wheels out of with similar upgrades good luck

Originally posted by paydro

the r33 gtst that they use is up for sale for $40 000 something i think which seems like a lot cheaper way to do it to me, they also said that the car is capable of alot more but there not touching it cause its for sale its 400hp at the wheels its suppost to be the fast 2.5 in the country at the time

400hp at the wheels is what I've got now with the NOS kit.

Originally posted by MELV

What would be needed to get the car into the 11-10's 1/4mile ?

How much money would need to be spend on the GTR to see 11's ?

and whats a good imported R33 GT-R worth ? im guessing around 45?

MELV

Well with a GTR you first have to decide what target you want. Do you want 11's, or do you want 10's

There is a HUGE difference and cost between the two.

Also a GTS-T is NOT a GTR, so dont compare the two....anybody.

its like saying "my mate bought a torana and did it up for a full cost of $50,000 and it ran 9's", and you spend 50k on a GTR and you get a clean stockish GTR.

If you want a clean GTR, a friend is selling his 33. Pm Leewah, or SIRVROOM.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...