Jump to content
SAU Community

Recommended Posts

have my 89 r32

ts got 240 rwkw on 15psi with heaps more potential.

-rb25 motor and gearbox.

-fmic

-has 102,000 on chassis motor not sure.

-been told it has a mod diff but not sure. done before import

-aftermarket fuel pump. not sure what it is done before import

-remapped r32 ecu for rb25.

remap was for standard smic, airbox and turbo as well as stock dump and stock exhaust to cat. ran 200rwkw on 10psi

rev limiter reset, no boost cut and no top speed cut

if remapped to new mods would make much more power.

-to4e top mount turbo with custom install

-turbo beanie. just been installed 1 week ago

-turbosmart pro gate 38 external wastegate with slip piece for screamer or plumb into exhaust

-full exhaust with custom dump

-ebc with high low boost. low is 10psi high is 15psi.

-ebc also has turbo timer not connected as well as

boost guage

output for nos and or water spray or what ever you want.

peak boost and average boost

current running voltage.

other stuff i cant remember.

tein ha coilovers.

cusco sway bars. f*kn massive about 35mm for front and rear

nismo 260kph dash doesnt look like its been tampered with.

flared rear guards to fit 18x11's which are on it atm.

upgraded 32 interior with no rips or tears.

genuine gtr front bar

panasonic head unit

2x jbl amps

jbl splits

2x jbl subs in custom box

jbl rear 2way speakers

momo steering wheel

have a 5inch tacho with shift light not installed.

i have the import approval papers

regency paperwork for compliance etc.

was insured for 17k full comp but since then added

front bar, stereo, wheels, suspension, ebc, turbo

prolly a few more things that i cant remember.

goin for full paint in 3days.

post-39965-1213864256_thumb.jpg

post-39965-1213864327_thumb.jpg

post-39965-1213864381_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...