Jump to content
SAU Community

Recommended Posts

have my 89 r32

ts got 240 rwkw on 15psi with heaps more potential.

-rb25 motor and gearbox.

-fmic

-has 102,000 on chassis motor not sure.

-been told it has a mod diff but not sure. done before import

-aftermarket fuel pump. not sure what it is done before import

-remapped r32 ecu for rb25.

remap was for standard smic, airbox and turbo as well as stock dump and stock exhaust to cat. ran 200rwkw on 10psi

rev limiter reset, no boost cut and no top speed cut

if remapped to new mods would make much more power.

-to4e top mount turbo with custom install

-turbo beanie. just been installed 1 week ago

-turbosmart pro gate 38 external wastegate with slip piece for screamer or plumb into exhaust

-full exhaust with custom dump

-ebc with high low boost. low is 10psi high is 15psi.

-ebc also has turbo timer not connected as well as

boost guage

output for nos and or water spray or what ever you want.

peak boost and average boost

current running voltage.

other stuff i cant remember.

tein ha coilovers.

cusco sway bars. f*kn massive about 35mm for front and rear

nismo 260kph dash doesnt look like its been tampered with.

flared rear guards to fit 18x11's which are on it atm.

upgraded 32 interior with no rips or tears.

genuine gtr front bar

panasonic head unit

2x jbl amps

jbl splits

2x jbl subs in custom box

jbl rear 2way speakers

momo steering wheel

have a 5inch tacho with shift light not installed.

i have the import approval papers

regency paperwork for compliance etc.

was insured for 17k full comp but since then added

front bar, stereo, wheels, suspension, ebc, turbo

prolly a few more things that i cant remember.

goin for full paint in 3days.

post-39965-1213864256_thumb.jpg

post-39965-1213864327_thumb.jpg

post-39965-1213864381_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...