Jump to content
SAU Community

Gtr Offset On Gts

noisia

By noisia,
in Exterior & Interior Styling

 Share

Recommended Posts

noisia Community Regular

noisia

Posted
Posted

will GTR offset clear and not scrape GTS guards? and does GTR offset look dope on a GTS?, like are they pumped enough etc?

sorry for being a n00b just i've done research and im still not 100% sure wot im getting myself into.

will 9 width on front be to much, do i need 8 width front instead?

will 215 stretch over 9 width?

cheers folk

Link to comment
https://www.sau.com.au/forums/topic/221633-gtr-offset-on-gts/
Share on other sites
adam-__- Grand Master

adam-__-

Posted
Posted

I don't know what 'GTR offsets' really mean, but if it just means wheels with offsets to fit flush on GTR guards then it will obviously stick out on a GTSt because they've got wider guards? With enough camber and flaring, I don't see why the most extreme wheels won't fit.

These wheels below would be pretty aggressive on a GTR, but they don't look too bad being on a GTSt.

post-32186-1212133268_thumb.jpg post-32186-1212133289_thumb.jpg

Fronts are 18x9 -7 with 225-40 FK452s.

Rear are 18x10 0 with 235-40 FK452s.

215s on a 9" wide wouldn't be a problem if you're after a 'stretch' look.

dori34 Grand Master

dori34

Posted
Posted

^^ omg adam, that black r32 is fken sex!!!!!!!!!!!! :P

it would fit with a roll or slight flare of the guard..

17x9+17 on the rear of my r32 4dr fit with just a roll of the guard..

fronts however i will need to flare as the design of the rim isnt made for big brakes so i added a 25mm spacer which brings the offset to -2 ....

funkymonkey Grand Master

funkymonkey

Posted
Posted

I had R32 GTR wheels front and back on my R32 GTS4, and the GTR wheels were about 5mm inside the gaurds. Didn't require rolling, but I didn't have the car super low either (twas lowered about an inch with about 3 finger space between tyre and gaurd).

noisia Community Regular

noisia

Posted
  • Author
Posted
I had R32 GTR wheels front and back on my R32 GTS4, and the GTR wheels were about 5mm inside the gaurds. Didn't require rolling, but I didn't have the car super low either (twas lowered about an inch with about 3 finger space between tyre and gaurd).

where the front and rear 9 width?

adam-__- Grand Master

adam-__-

Posted
Posted
adam-__- that's with flaring tho....

my 33 gtst has 18 x 9.5 +30 ssr professor sp1's and they are 10mm out of the guards (tyres streched and guards rolled)

Yeah, it was just to show how a wheel which would sit aggressively on GTR would sit on a GTSt. Wheels with those specs would be sticking out of the guards of a GTR with 'normal' camber settings and tyres.

Wheels which sit in GTR guards nicely wouldn't be too hard to make look good on a GTSt with some work was all I was trying to say/show with those pics. :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Wazmond
      WGNC34 Rear springs

      By Wazmond · Posted

      Try looking at Eibacb/H&R springs Thats what Gary sourced for mine.
    • AdiR34
      Fender flare widths across front/back of car

      By AdiR34 · Posted

      Hey y'all! I'm curious about how y'all go about widebodying your cars. I noticed that when running a square setup, my front wheels are a bit more tucked in than my rear wheels. Not by much, maybe 5-10mm. This leads me to wonder - when I widebody, should I use narrower front flares and wider rear flares? I found a set of 40mm rear flares that I really like, and was thinking of pairing them with some 18mm front flares, but I don't want the car to look strange. How have others done this? Note, I'm in a sedan. Thanks!
    • GTSBoy
      Stagea Front CV Axle Question

      By GTSBoy · Posted

      And if it was anything other than an auto tranny part, it might be a problem. But seeing as all auto trannies belong in the recycling bin, it's fine.
    • GTSBoy
      Stock rb25det neo questions

      By GTSBoy · Posted

      I have an R32 Fenix rad. It is good.
    • dbm7
      Stock rb25det neo questions

      By dbm7 · Posted

      All the schemas I can see, indicate your typical setup of ATF 'cooler' (read: heat exchanger) in the bottom radiator tank..ie; https://nissan.epc-data.com/stagea/wgnc34/5413-rb25det/engine/214/ ...but I can prattle on a bit here. These trannies have a thermistor in the sump ~ the TCU reads this and 1. bumps the line pressure up when the ATF is 'cold' and 2. prevents the TC lockup clutch from operating, until the ATF comes up to minimum operating temp (keeps the ATF 'churning' through the TC so it heats up quicker) -- trigger point is around 55C. In these conditions, the engine coolant temperature rises faster than the ATF temperature, and also helps heat the ATF up, which is why it's best to think of the in radiator tank setup as a heat exchanger ; the heat can flow in both directions... ...with these trannies, the 'hot' ATF comes out the front banjo bolt, flows through the cooler/heat exchanger, and returns to the box  via the rear banjo bolt. This gets a mention, due to the wildly different opinions wrt running auto trans fluid coolers ~ do you bypass the in radiator tank altogether, or put the cooler inline with the in radiator tank system...and then, do you put the additional cooler before of after the in radiator tank system?... ....fact is the nominal engine operating temp (roughly 75C), happens to be the ideal temperature for the ATF used in these trannies as well (no surprises there), so for the in radiator tank system to actually 'cool' the ATF, the ATF temp has to be hotter than that...lets say 100C -- you've got 25C of 'excess' heat, (slowly) pumping into the 75C coolant. This part of the equation changes drastically, when you've got 100C ATF flowing through an air cooled radiator ; you can move a lot more excess heat, faster ~ it is possible to cool the ATF 'too much' as it were...(climate matters a lot)... ...in an 'ideal' setup, what you're really trying to control here, is flash heating of the ATF, primarily produced by the TC interface. In a perfect world, wrt auto trans oil cooling, you want a dedicated trans cooler with builtin thermostatic valving - they exist. These should be run inline and before the in radiator tank system ~ when 'cold' the valving bypasses the fin stack, allowing the ATF to flow direct to the in radiator tank heat exchanger, so it works 'as intended' with helping heat the ATF up. When 'hot' (iirc it was 50C threshold), the valving shuts forcing the ATF through the cooler fin stack, and onto the in radiator tank heat exchanger...and you sort of think of it as a 'thermal conditioner' of sorts...ie; if you did cool your ATF down to 65C, the coolant will add a little heat, otherwise it works as intended... ...the 'hot' ATF coming from the front bango bolt, is instantiated from the TC when in use, so all/any flash heated oil, flows to the fluid-to-air cooler first, and because of the greater heat differential, you can get rid of this heat fast. Just how big (BTU/h) this cooler needs to be to effectively dissipate this TC flash heat, is the charm...too many variables to discuss here, but I just wanted to point out the nitty-gritty of automatic trans fluid coolers ~ they're a different beastie to what most ppl think of when considering an 'oil cooler'... /3.5cents   
×
×
  • Create New...