Jump to content
SAU Community

Recommended Posts

Hey all,

Im not going to lie to you peeps but evidently clutches/transmissions are not my strong point.

anyway moving right a long I have a bit of a clutch slippage issue which considering the age of the vehicle and the fact that i track it im sure the clutch is just worn out....But the slippage seems to be variable day to day. sometimes it slips like crazy sometimes its like its perfect again?

Is there an easy way of finding out if there is oil getting into the bell housing and causing or contributing to my slippage issue? I must say that when it does slip there really isnt a strong clutch burning aroma like I would have expected.

Cheers

Camden

Link to comment
https://www.sau.com.au/forums/topic/222049-oil-in-the-bell-housing/
Share on other sites

I would assume there would be a drain plug on the bottom of the bell housing... Haven't had the need to check mine so not 100% sure + im too lazy to back up my assumption.

Edited by Tomek
I would assume there would be a drain plug on the bottom of the bell housing... Haven't had the need to check mine so not 100% sure + im too lazy to back up my assumption.

haha but it does sound like a reasonable assumption. I'm getting the feeling i'll just purchase a new clutch anyway. even if it isnt completely rooted its probably about time to find something that is more matched to the cars power. (especially when i finally get back on the track)

Cheers

Camden

is the oil gearbox oil or engine oil you may have a leaky rear main seal letting go if you dont fix it you will end up with oil on ya new clutch

Mate i don't actually know if there is oil leaking or not.. thats why i was asking if there is an easy way to check. but since im pretty sure i'll change the clutch regardless im sure i'll see quick smart when i take the bell housing off.

Cheers

Camden

if oil was on the clutch once it would be stuffed as the oil soaks in and you can never get it out , (if its fibre) more than likely its slipping more when it hot, woiuld this explain it ?

I guess it does slip more when hot...but its hard to really say if your on the freeway (which is generally where i am 5 minutes from leaving my house) it will slip regardless

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...