Jump to content
SAU Community

Recommended Posts

I had a quick search on here and i can't find it. What is the RB25DET valve clearance ment to be?

I found the RB26 one which is 0.42-0.48mm on the intake and 0.35-0.41 on the exhaust but obviously the RB25 will be different becuase it is hydraulic.

I just wanna check it with the HKS cams and see if this is the cause of all this f***ing around.

Thanks guys.

Link to comment
https://www.sau.com.au/forums/topic/224608-rb25-valve-clearance/
Share on other sites

I thought you place a fealer gauge underneath the lobe of the camshaft and then depending on the outcome of that you replace the thickness of the shims? Isn't that it or am i thinking of something completely different? :geek:

Edited by PM-R33

Ok i just had a better look at the service manual and it appears that the valve clearances are the same for the RB25 and RB26, ill be damned. I would have been 100% sure they would be different, can anyone confirm this?

I thought hydraulic lifters don't need shimming as that is the whole point of hydraulic lifters.

Hmm so hydraulic heads dont have any sort of shims or anything in them? Only solid lifters? I wonder why Advan would say to check the valve clearances then :P

cos they didn't get the whole story maybe, like bubba said, hydraulic lifters don't need checking they pump up and hold when you start up your car. They only need replacing when they are shagged. ie don't hold pressure

OR maybe you got 26 cams.. did you get springs aswell?

26 cams & springs with hydraulic lifters I think leaves a bigass gap.

OR 26 cams with your stock springs and lifters would probably also run like shit as I believe the ramp rates for solid and hydraulic are different...

Nah they are definetely RB25 HKS Cams 256/264 (Part #'s RN172 Inlet, RN175 Exhaust) but it is still standard springs. The springs is the only thing that is still a bit questionable, would it really cause the car to run that crap though?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...