Jump to content
SAU Community

Recommended Posts

hey peeps thinking of getting these rimms for my car if they fit.

what do you reckon??from what i remember they measure in at:

front:19x9.5 35+

rear:19x 10.5 35+

post-42381-1214362132_thumb.jpg

and this is the car theyll be goin onto...

post-42381-1214362269_thumb.jpg

oh and any ideas on which rimms u think will look good let me know

cheers

Link to comment
https://www.sau.com.au/forums/topic/225440-yl859-versus-rimms/
Share on other sites

yea they look really nice in person. ive tried 18x12 rimms (didnt fit) and 18x11 with a crazy offset of -19 these were about an each too wide. so i was thinkg spacers on these. hopefully there wide enough as i really like the style

are the guards Dmax items? they look freakin sick so does the wheels ;D hehehe

not quite sure what guards they are but definitly not dmax. mine measure 75mm all around or there abouts. ive kinda got my head set on them just hope they fit ok

Yeah those widths are fat but they won't fill the guards with that offset. No worries though, just run spacers and you'll be sweet. More width is even more $$ on tyres. Some 20mm spacers might do the trick?

EDIT: I just re-read your post above about the 18x11 wheels that were an inch too wide with an offset of -19 (!!!). In that case you'll need bigger spacers than 20mm! Those guards obviously flare more than they look to me in the pics.

Edited by HuH
Umm offset? Don't think +35 is gonna look flush. You'll need at least -6 for that to fill anything. And don't buy rims with crap offset with the intention of putting spacers on.

yea thats wat im afraid of.yea the use of spacers is a last resort but just want to make sure to see what they look like.

you need +10 or similar offset with ur guards...

hmm the offset the guy gave me said it was a guess as the 19's arent in the country yet. the offset maybe lower.i know they wont sit flush but will just have to wait and see how they look.

and yea ill post pics when i eventually get them on :D

Why the hell did you bother getting wide guards and then intend on getting wheels that won't fill them at all? It will look like absolute crap. To get those wheels with a +35 offset looking decent, you'd need 100mm spacers and thats just not going to happen.

Those 18x11 -19 wheels will fit with EASE if you stretch some 255 tyres over them. Don't be weak, get them!

just measured the wheels and width today. standard wheels measure 6.5 yea. the width of the guards measure 85mm so thats about 3.5 inches making a total of 10inches wide to fill the guards

or am i missing something here??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What copper washer do you guys use on the bleeder bolts? The existing one I have I had no idea where to find it in a local store, I did buy some online but that are only 1mm thick whereas my old one is 2mm+ thick and when I put the new washer out and squeeze the top radiator hose I can hear a bit of air but not with the old one. Does this matter? The new one doesn't leak, but the inner diameter is a bit loose whereas the old one threads on the bolt.
    • Howdy all, after being out a few weeks ago on a spirited drive in my GTR I have 2 issues that oddly have appeared at the same time. Whilst accelerating quickly through the gears all of a sudden i’ve lost power at the top of third gear (below redline around 6000rpm) for no obvious reason.    From that point onwards the car has been running rich on idle, won’t really rev under load without a ton of black smoke and the odd backfire, and dying as a pull up to a set of lights unless I keep the revs up around 1500rpm. In addition when shutting down the car that same night (I was 10 minutes from home) I noticed one of the turbos was significantly noisy on wind down when shutting off the engine. After letting the car cool down overnight it starts up fine, although once it gets to temp the revs start to creep up and down, the exhaust is darker than it should be and it also sounds like it’s running rich (fat note) I’ve put a new set of plugs in it - no change, the old plugs all seemed OK with two of them being somewhat richer/fueled up than the other 3 with 1 being borderline. I’ve smoked tested the intake system via the front of the Turbos, found a split vacuum hose going to the factory boost gauge sender, which I have since replaced.  Also found another leak on the gasket coming off the rear turbo outlet, have also replaced this. After fixing both of these leaks - still have the running rich issue. I’ve also tried another pair of AFM’s - no change here After pulling off the front turbo intake pipes, there is obvious shaft play in the front turbo, which now hisses loudly on light revvs although I can’t see why this would make the car run funny even under idle. I’m curious to know why it’s running rich before I potentially replace/rebuild turbos. The car is completely stock <50,000kms  other than an exhaust. Oil and coolant are all clear. I haven’t bothered with coil packs as it looks like they won’t be the issue due to condition of the plugs. Any help appreciated as I cry myself to sleep!
    • No probs at all. I used to love trying to dig up obscure info for those in need where possible going back 20+ years on SAU.  I did have another look and couldn't come up with any closer match. I'm leaning towards those skirts in your first pic are custom fitments, cut down/extended or from another car entirely and modded to fit an R34 sedan. I would've thought someone in Japan had them and taken a photo at some stage over the last 2 decades but there's nothing. Someone out there must know surely.
    • Welcome mate. Any pics? Even with a DE I'd be well happy if I had that as a 1st car. 
×
×
  • Create New...