Jump to content
SAU Community

Recommended Posts

Heres the question...

i got a budget of around $800 - $1,000 give or take a hundred or so for a system for my r33... what you guys rekon i do? i'm talking the works, if subs where, where for the amp, how many speakers, etc... what would you guys do in my case...

i already got a deck- kenwood.... 50w x 4 blah blah blah... seen it in JB-HIFI for $499... nothing drastic in that... bought it when i got my car about 2 months ago not knowing what i would do (if anything) to the audio system for the future... the stock skyline speakers are finished, gone, done...

so what you guys think i should do? just interested in afew suggestions diff to mine...

Link to comment
https://www.sau.com.au/forums/topic/22557-advice-for-a-sound-system/
Share on other sites

When talking high quality systems that includes a sub and amp, a $1000 budget is a little small even given the fact that you have the deck.

But if that is the absolute maximum I'd suggest this (which is one we have done many times too just quietly)

Boston FS-60 6" splits at the front (doors and kicks)

Audison SRx4 amplifier

Jl 12W0 subwoofer

Stinger cable.

You would probably end up spending $1200-$1400 when you factor things like installation and sound deadening in but I tell ya what, the end result would be well worth it. :O

if you never plan to run subs, you can get a good set of splits and a pair of 6x9s and a small 4 channel that will do the job. A very cheap stereo i did for a guy, 1 x Alpine Type S Dual voice coil, 1 Alpine M200, Wireing kit from Autobarn and a set of cheap splits running off the head unit that was in hte car, cost, $600 neat, but that was building the own box out of timber that he supplied. It goes off its head too, the box is ported btw

Garys Car Radio - High St, Preston

For around $1100 I got (installed in my old vl)

2 x Clarion 10" Free Airs

2 x Clarion 6" Door Splits

1 x VNET2100 AMP (For Subs)

1 x VNET450 AMP (For Splits)

1 x Custom sub box install with 2 x 3" port holes to the parcel shelf. This was the best sounding stereo system I had heard for its price. It would outperform installs of 2k+

I already had my own head unit (just like u)

Yeah Fhrx has the idea,

Buy the best stuff you can afford, even if you need to lay buy.

AMP, SPliTS and Sub. Buy them in that order.

I wouldn't recommend a wiring kit for a Skyline, you don't need half that shit.

You'll need RCA cables long enough to go from the front to the back. About a metre of BIG power wire and a Metre of BIG earth. (get the same size)

And you'll need speaker wire to run from the amp back to the front speakers.

Check out the other threads in here.

Hey guys, just starting to look into the audio thing, so pretty unsure of all the specifics, but... can someone simply explain the concepts of chanels on an amp with reference to simply powering a sub. I was originally thinking of just putting in coax 6" in the front (or 6.5") and 6x9's in the the rear shelf, but i think i am turning away from the 6x9s and go the sub. I am at this stage just planning on having an amp for the sub, and just run the components off the head unit. Basically i want to check that there is no point in getting a 4 channel amp just for the sub, and what the consensus is on component speakers and needing their own amps. Bit long winded, probably as a result of me not really knowing much on the topic.

Cheers.

ofoofoo .. sub is always best for bass .. can't be beat with normal speakers ... if u're stuff for space ... go a 10" ... as for amp ... if its just for bass .. then get a monoblock amp ... they are designed just for subs and they are much more efficient for subs than a normal amp so u win with price/performance there ... i'm currently running my splits of the head unit right now and it works pretty good ... but if u really want it to sound good then get an amp ... an example of a good cheap system would be a cheap alpine monoblock ... about 300 ... 10" alpine type S ... thats about 150 maybe .. 50 for the sub box if u make it urself ... that will give u good bass ... forget the back speakers ... spend big on the fronts ... that will be a killer system .... good luck

Cheers hippy. Hopefully will spend my money in the right places - looking at DLS stuff. i think if i am going to spend the cash on decent speakers, should probably go an amp for the fronts. hoping to do it all for about 1600 (including head unit). i'll let you know.

cheers, was thinking car toys. Dont really know of anywhere else which has a good range of quality speakers (i need to check out some place called GT audio or something also). Have worked it out with friend - looking at two CA20 amps (1 x 170 WRMS), a classic series 12" sub, and hopefully the Reference series 6.5" components for front. add a couple of hundred for wiring/box, and with a bit of bargaining looking probably at $1700-1800. Then there is just a whole heap of work to do.

at the moment i cant do much but sit at home (doctors orders), but yeah i will come out (to a cruise) at some stage. Once i add some more stuff.. :D oh mine is black - absolute washing pain in the arse; true to what they say, the first black car you own tends to be the last black car you own.

$1000 isn't gonna buy you much in terms of quality really...but i guess what i'd do is

alpine type R splits or some focal polykevlar's 2nd hand - $350/300

or some Hertz splits new ~ $300

2nd hand Alpine Type R Sub or some RF punch's- $250

$100 for wiring and sub box building (4Ga)

Vnet 4100 2nd hand Amp - $300

or jaycar 4x100rms amp

no rear speakers, no point.

$1000 exactly

put in 100rms into each speaker, and put 200rms into the sub

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...