Jump to content
SAU Community

Recommended Posts

Hey all,

Im about to put some tein mono flex coilovers on a r33 gtst. But what im curious about is which orientation the lower bush at the bottom of the coilovres goes onto the spigot. one side of the coilovers bush is wider than the other and is also flared. (the stockies dont help as they seem symmetrical on either side of the eyelet)

from what ive searched on the forum so far the flare should be in contact with the bolt (facing towards the centre of the car) but im just still unsure as the crappy little pictures in the paperwork the came with the shocks could possibly mean the other way... but they are so ambiguous...

Cheers

Camden

Link to comment
https://www.sau.com.au/forums/topic/225743-tein-mono-flex-install/
Share on other sites

lol just posted up the same question for my tein super streets.. question answered.. cheers for posting the correct way :)

Did you buy Aussie or Jap spec SS? I only ask because the first person i spoke to at fulcrum didn't believe that any of there coilovers came with that type of bush setup we both evidently have..But maybe the Aussie stuff is different.

but i'm sure you got a similar manual to my mono flex... most useless drawings ever :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
×
×
  • Create New...