Jump to content
SAU Community

Recommended Posts

Hi Guys

Encountered this persistently loud screeching noise coming from my wheels when i was driving home today.

It sounded like two pieces of metal rubbing against each other.

The sound was only present when the wheels are in motion... its very loud and scared ths shit out of me

=)

Did a search through the forum and found that this problem is commonly attributed to worn brake pads/

Before I send the car down to the mechanic tomorrow... would like to check if the above is the probable cause. Would also like to hear from the fellow forummers what are the other possible problems im looking at...

Thank you

Cheers

Edited by ewhs
Hi Guys

Encountered this persistently loud screeching noise coming from my wheels when i was driving home today.

It sounded like two pieces of metal rubbing against each other.

The sound was only present when the wheels are in motion... its very loud and scared ths shit out of me

=)

Did a search through the forum and found that this problem is commonly attributed to worn brake pads/

Before I send the car down to the mechanic tomorrow... would like to check if the above is the probable cause. Would also like to hear from the fellow forummers what are the other possible problems im looking at...

Thank you

Cheers

Sounds like brake pads...That noise should be worse when you apply the brakes. Thonly other thing it could be is a seized wheel bearing ( unlikely - but possible ) I had one go on my old N13 pulsar...The vibrations that put throught the car....Shitbox..Get it fixed ASAP as you dont want to shred those discs

stick your head underneath the suspect wheel, bend the brake rotor guard away from the rotor (it's just pressed steel so can bend easily) and see if a stone falls out... then you'll save yourself some cash at the mechie

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...