Jump to content
SAU Community

Recommended Posts

Hi ppl,

I have been trying to install a stereo for the last two days (damn long condsidering i've installed about 6 units in other cars). The car is an R33 S1 2door. I have fixed my previous problems but have now run into some new ones which I need help with badly!

Problems are:

I have nowhere to mount the stereo! The original brackets are missing and I'm left with a nice double DIN sized hole. I need to get some sort of frame to mount the decks cradle to, and will also need a single DIN pocket. Question is, does anyone know of a dash frame/chassis from another car that will fit to the skyline? I need the actual metal bracket that fits two DIN slots, one for the deck and the other for a plastic pocket.

Other problem is the aerial connection. It looks like it has a weird plug shape with 2 prongs?! Anyone know of an adapter to mate the jap aerial to an aussie spec aerial?

Thanks in advance for any help.

cheers.

Link to comment
https://www.sau.com.au/forums/topic/22656-stereo-installneed-help-badly/
Share on other sites

go to ur local autobarn or car audio shop .. they will have the conversion adaptors for about 30 bucks ... so then u can install american or aussie stereos ... go to a nissan wrecker ... i think u maybe able to get brackets for pulsers and 300's to fit .. i'm not sure ... just find one that wrecks skylines :)

i had the same problem u will have to find other car brackets of make them ur self from cuts of metal which i did its a bitch to get the deck to be straight. You can get a din from nissan but they do cost $40 but the s15 one fits also which might be cheaper.

Do u have holes on the side of ya dash that u can screw onto if so ur lucky cause mine didnt even have that goodluck!

damn it!!!!! I bought the brackets from another wrecker (closer), but they aren't enough... the brackets I bought are kind of L shaped and fit deeper inside the dash, towards the back. There is no way I can fit a deck to them without it being about 3 inches deep from the facia. I spoke to a mate who recently put a stereo into an r33 and he said I am missing more brackets.

Is anyone on the forum wrecking an r33 with these brackets?? I would love to basically buy the whole bracket/cradle setup that goes with the deck right back to the internal dash rails.

i finally just finished getting that mother(*@#$ in!!!

talk about an absolute **** of a job.

Now the problem is that the dash doesn't clip back in properly (the facia around the stereo) and there is a slight gap under the DIN pocket.

Oh... and another problem.. Now my passenger side headlight doesn't want to work. I took the bulb out (what a bitch that was) and it isn't blown at all ?? It looks like a bad connection or old wiring. Anyone else have this problem? And can anyone else tell me how in the hell I am going to be able to get the bulb back in the headlight with the clip?

Firebladejr,

Go genuine with the brackets - you'll pay for them, but at least they'll be the right ones.

As for the funky jap aerial adaptor, I went to our old mate Dicky Smith and bought a single prong connector. Costs all of about a dollar. You can cut the old two prong connector off, and simple wire the new one on by twisting both cores together and soldering (obviously the ground sheath is the same).

I did this to mine, and there was no probs - surprised myself.

didnt u get mounting brackets with your head unit?

they fit in there snug, but i couldnt get the console back on.. because it stuck out too far.. it was a simple case of drilling new holes in the existing mounting frames.. to get the unit to sit deeper in..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
×
×
  • Create New...