Jump to content
SAU Community

Recommended Posts

Ok so have had enough of my car lately its been ff the road since february last year and have decided to sell off most of my parts and buy something that is a tad less modified and pref going, few reasons behind this but ne was, have a complete car that can either sell rolling or not otherwise will strip and sell off in parts.

Parts as follows

suspension and braking parts

7 point cusco safety 21 roll cage complete with padding, plates and all bolts to fit, non sunroon modle $850

Rear ARC 30mm adjustable sway bar $250

R33 gtst hand brake cables $100

G4 racing coil overs $800

R32 gtr tail shaft 2 piece $100

JIC rear strut brace $150

S14 front lower control arms $200 pair

S14 front hubs and spindles $350 pair

R32 gtr front rotors and calipers + brake lines and bolts and pads $600 freshly rebuilt can supply receites

R32 gtr rear brake rotors and calipers + bolts and pad $250

R32 gtr rear braided brake lines $50

R32 gtr complete rear diff in housing $400

R32 gtr rear drive shafts and hubs $300

(or will sell complete rear cradle for $1000)

Interior Parts

Schroth 4 point harness $100

r32 gtr passengers seat $100

bride copy fixed back drivers seat on genuine bride rail $250

momo sports steering wheel with silvia boss kit $150

autometre monsta tacho $250

stock s13 silvia dash with cluster and 4 gauges above glove box, oil temp, oil pressure, volts, water temp, $250

Exterior Parts

Turbo back 3" exhaust, 3" dump, front race cat and cat back to suit ca18 $450

onevia conversion

180sx bonnet stock with sparco bonnet pins

180sx front guards

180sx stock sr20 front bar

180sx gp sports front bar

180sx head light covers + vented passengers side

180sx headlight motors

Sell the lot for $600

Engine Parts

Complete ca18det forged engine with all receites

Os Giken twin plate clutch

ca18det 5 speed manual gearbox

Dr Drift remapped computer and stock wiring loom

Greddy oil coller kit with remount mount

600x300x100 FMIC with custom piping and turbo smart vee port

Garrett Gt3071r turbo kit on ss low mount manifold and 38mm external Waste gate

Bosch external coils with loom

Custom plenum creations custom plenum with 75mm throttle body

more info can be found on the motorand build on the below link.

Selling complete motor and gearbox as a package for $6000 firm WILL NOT SEPERATE, if dont sell will keep

http://www.nissansilvia.com/forums/index.p...howtopic=272094

and once thats all gone will have the shell left over can be regestered still as it just about out of its 3 month period, can supply import approval paper work as well.

As for pictures off all parts they can either be found at the link below otherwise msg me and ill arrange individual pictures of each item.

http://www.nissansilvia.com/forums/index.p...howtopic=272094

All contact via pm please. And as for prices they are all semi negotiable so pm me with your best offer if you dont like my price and ill see what i can do, will discount if you buy alot of gear at once.

All parts located in Hobart Tasmania and will post at buyers expense.

cheers

Stephen

Hi sven

The rear diff in housing your selling do you know how many km's it has done please and ratio do you recon?

Also you said you have a complete car as a rolling sell. what sort of car

regards stuart

Edited by NISSANGTS
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The ATTESSA is functionally identical to R34; there were a bunch of JDM models that continued ATTESSA including Fuga/Q70, Skyline/Q50, Cima etc as an option. All with Auto only and I think mostly for snow regions. AFAIK there were no AWD VR30DDTT sold in Australia - it is on my to do list to check regs for racing a LHD car in Targa/ATR/AASA/CAMS events because if I can get the auto to work it would be interesting to run a 4wd car The Ecuteck TCM tuning is the same model as their ECU tuning, they already have it for R35 and Dose's favourite, BMW. You buy "points" to allow your computer to be tuned, buy either a bluetooth (phone app) or bluetooth+USB+Key (phone and PC) dongle, and pay for a tune that will be locked to your tuner ( ). You can also access the tuning software yourself but 1. it is mega expensive and 2. these computers have a billion parameters that intersect, so how could you ever spend enough time on it to get a decent result.
    • Or, is it a case of what it is like owning an R series Skyline? NFI what the previous owner has done or fiddled with... Ha ha ha After reading through this thread, I went on a bit of a research about the Q50/Q60. Now I'm quite intrigued by them! Is the AWD in them more like a WRX where it's always AWD, or is it more like the ATTESSA in the GTRs? By the sound of this TCU tuning, this sounds like a case of someone has made some real software for it, and you just need the right piece of hardware, and then you license that specific vehicle/TCU. Or is this a case of the software will be really expensive so only a few tuners have it, and you still have to pay a license per vehicle?
    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
×
×
  • Create New...