Jump to content
SAU Community

Recommended Posts

In case anyone is interested there's a great thread in forced induction on a new Australian plug in ECU for rb20/25/26

http://www.skylinesaustralia.com/forums/Pl...ng-t218179.html

Briefly :

Direct plug and play replacement ecu board

full usb software tuning

switchable maps

uses all factory sensors

built in map sensor

boost control

launch control

antilag

built in factory base map for local fuel

australian built with full support and warranty

much much more

Cost will be around $1650 . Although more than a base powerfc , if you add up boost controller , map sensor or AFM upgrade and laptop software for PFC its pretty competitive - a 2nd hand rb25 power fc and decent electronic boost controller is probably more.

Were hoping to have the 1st units early next week and we will be carrying them in stock.

I am posting here as I think its pretty big news given the lack of power fc options for rb25/20. If any mods think that's not appropriate feel free to move to the sponsor sale section and my apologies.

  • Replies 91
  • Created
  • Last Reply

Top Posters In This Topic

anyone who can tune a powerfc/wolf/haltech/motec/autronic etc will have no problem . software is very good and stable

well also be able to arrange tuning for them

hows the tuning time going to compare against something like a powerfc? will more time be needed on this new ecu which would mean more tuning $$$ or is it easy to work with?

hows the tuning time going to compare against something like a powerfc? will more time be needed on this new ecu which would mean more tuning $$ or is it easy to work with?

early reports are tuning software is great . easy to use and reliable . time will be similar to pfc or any other popular ecu

tuners I have spoken to over east are quoting normal tuning prices same as pfc

So I can hook up a laptop if I have the right cable and adjust the boost or can only tuners modify it?

usb is built in , plug into your laptop and tweek to you hearts delight . im not sure on tuner lockout options at this stage but certainly its not a requirement

also has the ability to run multiple maps via assignable input , ie multiple boost settings . I believe cool stuff like gear/rpm dependent boost mapping is also supported (have to confirm )

Edited by autoworx
can these be used without AFMs? like a d-jetro? as my AFM's seem to be stuffed..

Yes.

Briefly :

Direct plug and play replacement ecu board

full usb software tuning

switchable maps

uses all factory sensors

built in map sensor

We will be putting one on our "big china turbo" equipped drift/track bunky r33 for testing purposes.

the forced induction thread linked at the top is getting the first few install reports coming through and they seem to be awesome

1st shipment arrives today!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
×
×
  • Create New...