Jump to content
SAU Community

Recommended Posts

Hey

I was cruising with some friends and we went through Southport and saw like 20 cops in patrol cars parked in a parking lot all talking to each other.

So while we were driving slowly passed we decided to cruise around places that they weren't likely to go.

also saw a undercover Aurion which pulled over a 4WD and a undercover Commodore pull over someone else.

Just wondering if it was a Blitz getting prepared for the Saturday night?

here is the map of where they were.

post-39868-1215935145_thumb.jpg

Edited by Greddy Skyline
Link to comment
https://www.sau.com.au/forums/topic/227927-police-blitz-last-night/
Share on other sites

It sure was.

were you out last night or were u being sarcastic ?

I was just shocked to see so many out in one night.

Its been a while since I've been on a cruise so yeah and I haven't been around surfers for long time.

Yeah i saw a couple around.

I went through a road block at springwood where they had a WRX and another car with their bonnets up.

i would say that was my mates wrx. he got done for being too loud, wheels to big, blow of valve and gauges somewhere in springwood the other night

they can get you with big wheels? i just got a set of 20's on my r33

i would say that was my mates wrx. he got done for being too loud, wheels to big, blow of valve and gauges somewhere in springwood the other night

They have to be the same diameter as factory including rubber +15mm or -26mm. So if you get some real low profile tyres you could probably go an extra 1"

As quoted from QLD transport light mod guide:

"The rim diameter may be varied from the standard size

but the overall diameter of the tyre must not vary by

more than +15mm or -26mm.

These limits have been set for a number of reasons.

Varying the overall diameter of tyres affects ground

clearance, centre of gravity, brake effectiveness, steering

geometry, performance and speedometer accuracy."

With 20's on a r33 your fecked :D

Edited by ToMMaH

off topic but the other night i seen a black liberty with tinted windows... with some 1 pulled over nd lights flashing on the dash.. you would never guess it was a d car.. nd around my area theres a sh#t load of xr6 turbo unmarked cars..

They have to be the same diameter as factory including rubber +15mm or -26mm. So if you get some real low profile tyres you could probably go an extra 1"

As quoted from QLD transport light mod guide:

"The rim diameter may be varied from the standard size

but the overall diameter of the tyre must not vary by

more than +15mm or -26mm.

These limits have been set for a number of reasons.

Varying the overall diameter of tyres affects ground

clearance, centre of gravity, brake effectiveness, steering

geometry, performance and speedometer accuracy."

With 20's on a r33 your fecked :)

I dunno bout 1" man.. i got a 32 gtst. n i got 19s on it.. cops got there book out said they were too large. Said if i go 2 a 30 profile instead of 35 i am sweet.. :rofl:

All you need to do is find out standard rim and tyre diameter that they came factory with, and then change your rims and tyres to your hearts content within the limitations of QLD Transport..... speaking of which, anyone know the TOTAL diameter for a 34gtt? Me thinks I might need to look at getting rid of some things that keeps the rims off the brakes sometime... Can't use the "but I bought it that way from the dealer excuse" if I get pulled up for the little bits of metal....

Edited by Doze

yes i see that my speedo is out by 7kms when doing 100km, i have 255 25/20 on back and 245 20/20 on front, pretty small rubber band on the front lol

yes u can only go a certain amount of inches over ur factory wheels.. something 2 do with rolling diameter. When u go too big or change profiles by a massive amount it puts your speedo out n shit.

post-47818-1216777919_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • sold listed as a Tomei LSD 1.5 Way For 1998+ Nissan Skyline ER34 25GT RB25DE w/Open R200 https://www.ebay.com/itm/174006114594?campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=&mkrid=711-53200-19255-0&loc_physical_ms=108689&loc_interest_ms=&campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=71883f2ccc571356e0a757bc7adfdde2&mkrid=710-53481-19255-0&loc_physical_ms=108689&loc_interest_ms= it went in like butter all gears, alignment, back lash etc, rotation and clearances correct, and if rolling all rotates smooth and free when coasting down road , clutch in or out over 10 mph smooth... its the binding, clunking and jerking from a stop that is most concerning, also seems like its going to tear the tires off in 10 miles of normal road driving. 
    • What 1.5 way? There's no such thing really as a 1.5 way, just different ways of explaining 2 ways with different ramp rates. HOWEVER. In any driving in a straight line your 1.5 or 2 or 1.7 way should have no clunking at all. With the clutch fully depressed the diff should be silent (unless it's welded but I'm assuming it's not). Something aint right here.
    • Clutch is a spec brand, new clutch system,( PP, flywheel, friction disc, etc. pull type) installed 100 miles ago, with no problems.
    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
×
×
  • Create New...