Jump to content
SAU Community

Recommended Posts

ECUTalk Consult LCD V2 Displays

protoplastic.jpg

2005 prototype showing blue screen (4MB) - just happens this video from very first prototype, uses the blue LCD available for this display. Note the blue screen isnt as visible in competing light than green, keep that in mind when deciding which LCD to get. Although that was prototype from 3 years ago, the main sensor display is similar (instead of ECO:xxx its xx.xL/100KM). Also the update speed there i think is about half the speed of the current one.

Following on from the previous V1 thread, I've almost completed V2 displays that improve on the V1 displays in quite a few areas (can be seen in the 'changes in v2' section on the website). One key change is user updatable firmware (like adsl modem or computer bios), so when I add new features (perhaps logging to microsd card, audible alerts with the buzzer, etc) you will be able to upgrade your display to get the new features.

The display is plug and play into the consult port and requires no wiring (so its portable also). Your consult port is located near or attached to your driver's side incabin fusebox. You will need a car that:

a) supports consult (mostly evidenced by the consult plug near your fuse box, few late model Patrol etc will have port but not support consult for ECU), and

b) still retains the stock ECU (piggybacks and remaps generally fine, but PowerFC etc wont work), and

c) doesnt have messed up wiring to consult port (shouldnt, unless you have an engine transplant or some other reason the wiring may have been messed with)

For Skylines, this is the R32's (10/89+), R33, R34. If for whatever reason the display doesnt work for your car, if its returned in original condition you can get a full refund (minus postage).

Display Hardware:

The unit is 144mm wide, 48mm high, and 33mm deep (buttons protrude 3mm), and weighs ~250g. It is smaller than DIN size (180x50mm) and as such could be mounted in the DIN slot, amongst other places. It has a USB port for the integrated consult interface (accessed via the menu) for those who want to use it with normal consult programs on their PC, and for firmware upgrades.

The unit has 2 buttons on the front (they will be black, rather than the red/white ones in picture), a menu/enter button (the left one) and a cursor button (the right). The buttons are used to navigate through menus and the different features of the device. The menu/enter button initiates the menu (from the main display screen) or selects the currently selected item from any other menus/screens. The cursor button control the position of the cursor mainly in any of the menus, and switches between the sensor display or trip meter screen on the main display. It should be pretty easy to work it out when you use it.

The screen is a 20x4 backlit screen, wide temperate (-20 to +70 operating, -30 to +80 storage), available in standard green, or white on blue ($5 extra). The cable can exit the right or the rear, so it can be flush mounted either way.

protoplasticsides.jpg protoplasticrears.jpg

Display Features:

  • Trip meter: Shows current speed (kmh or mph), current fuel economy (L/100KM or MPG), and for the current trip: fuel economy, fuel used (L or G), fuel rate (e.g. LPH, litres per hour, or GPH), distance travelled (KMs or Miles), and time elapsed.
  • Sensor Display: Shows current speed (kmh or mph), rpm, battery voltage, current fuel economy (L/100KM or MPG), injector duty cycle (%, and both if car has 2 injector banks), ignition timing, AAC, O2 (both if car has 2), water temperature (C or F), AFM (both if car has 2) and TPS (volts or %)
  • Fault Codes: Displays any current fault codes, along with how many starts since the fault code last occurred. Allows fault codes to be cleared.
  • USBIF: Enables the USB consult interface. Also shows the amount of bytes received/transferred from/to the PC and the last 4 bytes sent/received for some excitement.
  • Max Values: highest values recorded for speed, rpm, water temp, injector duty cycle, TPS, AFM, ignition timing. Allows the max values to be cleared also. Max values are for current trip only.
  • Time Trials: allows you to enter time trial mode, where it will record time from 0 to 60, 100, 160, or record from 0kmh until you travel 400m (i.e. quarter mile). Of course this is not to be used on public roads. Best times are saved into EEPROM (lost when you update firmware most likely).
  • Info: read some boring stuff about who made the display, and the firmware version.
  • Options: set injector cc size and number of cylinders for fuel/economy readings, set LCD brightness/contrast, setup TPS% min/max, KM or Miles, C or F, TPS volts or %, and allows you to reset display for firmware upgrades.
  • (Note: Options->TPS setup): As TPS only uses 0.5v-4.5v range roughly, not full 0-5v, if you set it to % without setting up min/max, it will read ~10-80% from closed to fully open. To setup TPS, you just need to have the TPS like it would be for 0% (foot off) on main sensor display, then go into setup tps and set the 0% point to current TPS value. Then go back to sensor display and go full throttle (ideally car 'on' but not running), then back into setup TPS and set 100% value. Then it should read 0-100%.

Price, Scheduling and Payment:

$200 pickup or +$7 for express postage. Blue screen is $5 extra. $5/unit sold will be donated to SAU. Thought price would go up from V1 displays due to getting more of it assembled elsewhere rather than doing it myself, but this was offset by the higher quantity batch this time, so can keep it a nice even $200 for group buy. Keep in mind USB consult interfaces alone are ~$110, so for less than double that you're getting the integrated usb interface + display itself.

Estimated availability is in August. I'm currently waiting on enclosure manufacture before displays can be sold. Initial run will be around 90 displays split between SAU, PGA and people who have contacted me via the website. If all 90 sell then ill aim to get another batch done.

Payments will only be asked for when ive confirmed that a device is available for you. Payment is via bank transfer (St George, arrives day after at earliest), or Paypal (instant, but has an additional fee of $6 unfortunately). Paypal is only an advantage when bank transfer is inconvenient, or you want the device ASAP (eg its 8pm and bank transfer wont be processed till the next day, and arrive in my account the day after that). You dont need a paypal account necessarily to use paypal, just a credit card.

Pickup is from Blacktown, Western Sydney, or possibly near Wynyard in Sydney (I work there a couple days/week).

I want one, what do I do now?:

Send me a PM stating your LCD preference (green/blue, only indicative for ordering purposes, you make final decision when you pay), and a contact email address (for backup purposes, also for notifications of firmware updates etc later on). I will then add you to the list (see second post). Displays will be allocated to people in the order they have express interest and have subsequently been added to the list of interested people.

As I make the displays, I'll ask the people in the list via PM in turn if they still want one, and if so, request payment. If they can provide payment within a reasonable time, they can purchase it then and pickup/get it posted. Otherwise, they'll either be removed from the list or put to the end of it, depending on whether theyre no longer interested, or just cant pay right now.

Things ill ask for when I've got displays ready and you're next on list:

1) Your full name

2) Your address and phone number

3) Email address (if one hasnt been provided already...for firmware updates in future)

4) Your payment method (bank transfer, paypal (+$6 fee), or pickup). Bank/paypal details will be provided at this time.

Peter

protoplasticfronts.jpg

Link to comment
https://www.sau.com.au/forums/topic/228314-ecutalk-consult-lcd-v2-displays/
Share on other sites

  • Replies 82
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Interest List

please refer to this link (and search for your username) to see your position on list. cant put the list in this thread as we cant edit posts anymore.

Hey Peter,

I have found that i have a consult port and i am still highly interested in this but i recently had an engine swap (same engine). How can i possibly test if the

consult port is working. I have a basic electronic skills and can test for power via a multimeter. Could you help me out on this before i purchase one of

these!

Cheers

-Min

http://www.ecutalk.com/images/consult_car.jpg

confirm ground is connected to ground, 12v gets 12v when ignition on (or car running), forget chk/check (not used), and the remaining 3 should be short circuit/low resistance with their respective pins on the ECU itself (grab a ecu pinout...pins are nearly always around the bolt/middle of ecu pins)

but if you cant be bothered, if the display doesnt work for whatever reason and its returned in original condition in a reasonable timeframe (e.g. a week or two), then you can get a full refund (minus postage).

worst case you can probably chop off ur consult port and re-wire it at the ECU...i did that for RB25DET silvia i had 3-4 years ago.

is there any chance that this will ever work with a power fc?

never, nissan would have patented it probably, so if apexi implemented the same thing they would have been sued probably. even if they didnt, apexi didnt implement consult capabilities so thats all that matters.

ahh i see, i thought this thing was taking raw data from the sensors at the ecu and then it goes from there, but i now assume that everything is done in the ecu and this is just a display.

yep, its plug and play into consult port (which connects to ecu), no wiring or other messing around. so it has the potential to do anything that can be done via consult

when my new engine is done i will go with the power fc purely because i already have it and need to save a bit of money but i will probably change to a dr drift remap so i might grab one then.

http://www.ecutalk.com/images/consult_car.jpg

confirm ground is connected to ground, 12v gets 12v when ignition on (or car running), forget chk/check (not used), and the remaining 3 should be short circuit/low resistance with their respective pins on the ECU itself (grab a ecu pinout...pins are nearly always around the bolt/middle of ecu pins)

but if you cant be bothered, if the display doesnt work for whatever reason and its returned in original condition in a reasonable timeframe (e.g. a week or two), then you can get a full refund (minus postage).

worst case you can probably chop off ur consult port and re-wire it at the ECU...i did that for RB25DET silvia i had 3-4 years ago.

never, nissan would have patented it probably, so if apexi implemented the same thing they would have been sued probably. even if they didnt, apexi didnt implement consult capabilities so thats all that matters.

Thanks Peter. I guess if it is not connected i can just re wire it into the ecu.

Cheers

-Min

they were supposed to ship the enclosures on thursday but havent heard from them yet. hopefully they ship by sometime next week so i get them sometime the following week.

heard back from them, were delayed due to people taking vacations or something...they didnt give an updated ETA but id hope ill have them by august 9/10 weekend.

here are some pics of the blue screen. first one is better quality but the blueness in the screen is a bit washed out (i.e. it doesnt actually look that way). the second shows the blue aspect of the screen better (but was taken at night without flash so picture quality itself is worse). also shows the black buttons which will be used rather than the red/white ones.

post-4553-1217470108_thumb.jpg

post-4553-1217470288_thumb.jpg

That looks awesome.........!!! Black buttons make a difference too. I still cant wait for it. Any chance i can get one earlier :down: if i pay now *ahem* :P

Also have you ever thought of like a rubber grommet for the USB port at the front? I can just see lots of dust and crap getting in there over time.

no chance :cool:

good news is they have shipped and i might get them monday! and ive taken mon-wed off work to get some of the final assembly done so hopefully not long now!

i did have a look before for grommet, but didnt know what to search for. found a bit more today, like this:

http://www.l-com.com/item.aspx?id=8134

http://www.amphenolcanada.com/ProductSearc...MUSB2D11004.pdf

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
    • Oh, and as for everyone with their fuel economy changes, I switch between E10 and 98 in the company car. Even do when I had personal cars that could run on E10. You know what changed my fuel economy in any noticeable way? How I drove, and where I drove. Otherwise, say on full tanks of just back and forth from work only (So same trips, same sort of traffic), couldn't notice a difference that I can correlate to the type of fuel in use. In the current vehicle, that's over 42L of USABLE fuel. While 98 is all "more energy dense", it also has higher knock resistance as it takes more energy to get it to ignite too. The longer hydrocarbons, typically more tightly bound. So running the same ignition map, can also produce less power, if there isn't enough time to get it all burnt through properly, as yep, the flame propagation speed is different from lower octane fuel to higher (Higher has a lower flame propagation, due to the more tightly bound and harder to self ignite funs. This is also typically where, a vehicle that is designed purely to run on 91 (Whether it be E10 or normal 91) usually sees absolutely no real world difference in fuel economy for the normal man, woman, or dog.
    • We've got some servos around me that have 91 with E10, 91 (no E10), 95, and 98. At those stations the change from 91 E10 to 91, is typically around 8c/L.   But lets not get started on the price of fuel in Oz. It's ridiculous. All the service stations around me, bar one, the price of fuel has been over the $2 mark per litre for the cheapest, 98 being around $2.45. That one service station is a CostCo, fuel from it comes from the same refineries, and makes no pitstops, it runs great, including the 98. In fact, I've had no issues on CostCo fuel, but plenty of issues at other stations!. The CostCo fuel, was $1.65 roughly this week for 94 with E10. $1.88 for 98. Servos directly across from it, $2.10 for 91 E10, and $2.48 for 98. The part I had to laugh at? If I drive multiple HOURS away from Brisbane, say out near Nanango, or Kingaroy, or even out to Goondiwindi, the price of their fuel, is the same as what it is at the CostCo... Oh, and that BP servo at Goondiwindi is HUGE and goes through epic turnover of fuel, so it's not sitting there for weeks going to shit. And what blows me away, my mate is one of the people who drives the Fuel Tanker all around QLD, delivering to all those places. At the same company his previous role was doing the "local haul" deliveries... Same truck, same driver, same pickup point it all comes from. So you tell me, how the hell it is 60c/L CHEAPER for fuel, when nearly all else is equal, except they require a B-Double to drive half a day out of Brisbane, and half a day back, every second day, compared to the delivery that can be under 30 minutes drive from the fuel pickup point... Not to mention, go five blocks down the road, and Ampol to Ampol will vary 30c/L... And I've had this conversation with my mate... The way it's priced, is just typical, pure and utter rubbish... He also does runs from Brisbane, to all over QLD, down to Newcastle, Sydney, Nowra, Melbourne, Geelong, and even out to parts of the NT depending on the companies needs. His main stuff is all the longer distance away from home for a few days at a time, then when he's back, he loves to just pickup extra shifts wherever he can in whichever truck, hence all the weird different places.   Oh, as for getting E10 into all the fuels in Australia... It was very quickly highlighted, that we don't have enough biomass available to use to make E10 sustainably like they require, and it would dramatically cut into our, and the worlds food chain supply...   I vote we all just start running on liquid methane gas... Plenty of that just getting tapped off at tips from underground decay... (Note, this is pure just stupid commenting. I could very easily highlight the reasons its not a good idea especially on scale...)
    • Am I correct in assuming that the R35's are getting the classic skyline haircut off the odometer?  Quick search on carsales, there are 33 08 and 09 GTR's for sale, only 2 of them have more then 100,000km's on them (116,075 and 110,000 respectively).  And somehow there are about 25 for sale with around 60,000kms? Looks like the classic skyline haircut to me =/
×
×
  • Create New...