Jump to content
SAU Community

How To Tell If Its A Push Or Pull Clutch?

R31 Gagz
 Share

Recommended Posts

R31 Gagz Collaborator

R31 Gagz

Posted
Posted (edited)

Hi Everyone,

I have doubts that my 1989 R32 GTR has the original gearbox and clutch, how can I tell for sure whether it's a push or pull type clutch?

I do know it has to do with which side of the clutch fork that the slave cylinder is on, but I cannot find anywhere clarification on which is which. What type of clutch is it, if the slave cylinder is on the engine (or front of car) side of the clutch fork? If I can find this out then it obviously also answers for the opposite side.

Please only post if you know for sure as I've already read enough threads on here and GTROC UK where the information is incomplete or there are conflicting opinions...I need facts!

Thanks to everyone in advance :D

Cheers!

Craig

Edited by R31 Gagz
Duncan Grand Master

Duncan

Posted
Posted

Its dead easy....look at the way the clutch slave rod points.

If it points to the front of the car it is a push clutch. If it points to the rear of the car it is a pull clutch.

So yours is pull if its on the engine side and points rear. Good score in an 89 GTR.

Swiper the Fox Grand Master

Swiper the Fox

Posted
Posted
Its dead easy....look at the way the clutch slave rod points.

If it points to the front of the car it is a push clutch. If it points to the rear of the car it is a pull clutch.

So yours is pull if its on the engine side and points rear. Good score in an 89 GTR.

its the opposite of what is said above.

Swiper the Fox Grand Master

Swiper the Fox

Posted
Posted
good point....I shouldn't stand on my head when looking under the car :thumbsup:

cool...now R31 Gagz...if the rod out of the cylinder is pointing rearwards its a push (actual cylinder is positioned in front of the clutch fork) obviously the other way is pull.

R31 Gagz Collaborator

R31 Gagz

Posted
  • Author
Posted
good point....I shouldn't stand on my head when looking under the car :down:

You had it right...in a way :rofl: ...na thanks mate :D

cool...now R31 Gagz...if the rod out of the cylinder is pointing rearwards its a push (actual cylinder is positioned in front of the clutch fork) obviously the other way is pull.

Thanks DG, that's exactly what I was after :rofl: ...by the way if that's your gtr in your avatar, very nice...read the article on it the other week, 9sec twin low mount....crazy!

Cheers!

Craig

PS...mods, could this thread be stickyd or the information added to an FAQ, it was very hard to find :D....thanks

R31 Gagz Collaborator

R31 Gagz

Posted
  • Author
Posted
Why the difference, are the later pull clutch designs more efficient or better or?

Hi Ben,

Yeah really not sure either, possibly it just works better? The pull type clutches cost slightly more than the pull type, so that's one con...you would hope there were some good pros for paying more :blink:

Does anyone else know why they changed to a pull type clutch on post 1993 model R32 GTRs?

Cheers!

Craig

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      boost source Size Garrett gt28 gen2

      By TurboTapin · Posted

      You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • QB6SAGR
      Battle of the broken skylines

      By QB6SAGR · Posted

      Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Rezz
      Spotted on the street....

      By Rezz · Posted

      Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...