Jump to content
SAU Community

Recommended Posts

Which tyres are good for road + spirited driving and the ocassional drags without burning a hole in my pocket ?

Looking at 235s and 255s

one more thing, whats the largest width that would fit under GTST guards ? both front and rear ?

*thanks guys*

will really appreciate your help. Thanks again !

:burnout:

Link to comment
https://www.sau.com.au/forums/topic/22938-which-tyres-are-good/
Share on other sites

i'm running 275/30/19 in the back falken 451's

they are ok new ..a bit slippy after 5000 k's

Preceda's come in 245/35 only for 19's but have heard some good reviews..about $ 560 ea

i found some hankook k104 's for 400 ae 275/30 but dont know how good they are ...they look huge though :D

Originally posted by EnricoPalazzo

Simex baby! Good for launches!

i had them, they were pretty good.

not i've got a set of the new Dunlop 3000A.

they shit all over the simex. The use them on XR6t/XR8's.

they are very decent.

and what rim size you got?

if you've only got say... 16x8 then it's useless going to 255's

OK I have had the following - all either 235/45/17 or 255/40/17

Goodyear Eagle something - can't remember, cheap, and shit, no grip, but very quiet

Falken GRB FK451 - excellent corner grip, not so great off the line, and still gripped well when worn and pretty quiet

Falken Azenis semi slick - excellent grip when warm, lasted about 6 months, very noisy, not mcuh grip when wet/cold

Falken GRB Tune II - cheap, and it showed - not much grip, in corners or straight line, noisy and lasted about 6000km - but for the money not too bad

Bridgestone S03 - So far so good, heaps of grip in the dry and wet, really quiet - done about 3000km so far and they still look pretty new. On the front now

Bridgestone RE55S - semi slick, heaps of grip - if I can get 10,000km out of them I'll be happy!!, not noisy, good in the wet so far (only 45okms so far!!) No wheelspin in 1st - well priced for what they are, and if you have a bit of grunt, these will get it to the road- so far they are great

And yes, my car gets a thrashing, and goes through its fair share of tyres!! GRB FK451's for value - S03 for pure performance

Hope that helps

dunlop fm-901's are apparently mad. They do well in comparisons such as motor tyre tests.

otherwise maybe try some michelins, my parents have always hed them on their car, and the grip is unbelieveable for the size... not sure which mdel but they wernt even very expensive. WE got P6000's as replacements (on my advide) and the difference in grip is huge, the michelins gripped a million times better...

My friend got 901s for his car in 17/255 17/235 like u, 250 for front and 350 for back from tempe tyres. They are a bit noisy, but excellent grip/handing in wet and dry.

siksII

you got me thinking has anyone done a comparison between top of the line michelin and pirellli tyres on grip

michelin cost over $500 per tyre

pirelli only $380 per tyre

on price for same features I went pirelli but no test drive.

So regarding the michelins can you find out which model?

Are you talking straight line grip or cornering grip?

fm-901's make nice white smoke when they spin and due to their lower grip you feel like your riding harder rubber.

Warning - P-Zeros are very very quiet! although a corner you wouldn't go over 70kph in a brand new volvo you can do at 120kph with PZero's in your skyline, JUST RIDE IT OUT! No drifting!

The time I did that my brakes got too hot and I couldn't slow down enough before the turn. takes about 1 second to drop each 10kph when your brakes are overheating. Freaky.

90 degree left turn - can take at 90kph - 40kph higher than an excel with slightly wider triple sidewall temperature A warmed up tyres. at 50kph.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • (it is a brand new ported mellings pump) I suspect the lack of pressure is due to the leak. It was *not* that low in other logs of oil pressure in the past. It wasn't that hot either, but not far off.
    • Would a Mellings oil pump be a viable option  From my time with a LS, and talking to tuners and LS specialists, the "weak" OEM oil pump is one of the first things they recommend to swap out if I was going to give the engine any high RPM I opted for a Mellings high volume, with the high pressure springs and I never had a issue with it Cost wise they are not expensive in the scheme of things 
    • Just bought a 2002 Stagea 250tRS VR-X Four AERO VQ25DET and spent the last two weekends cleaning and detailing it.. still have to do the wheels and the engine bay but the rest of it came up nice. Imported 2011 to S.A. and I'm the third owner since it was imported. I met the guy who brought it over, he went to Japan and picked out the car, bought it and ordered the wheels. He also gave me a list of stuff he did to the car with receipts. Coil overs (I have the original springs), 3" exhaust from the dump pipe back no cat, Custom dump pipe,(I have the original exhaust), Plenum spacer, 18" custom Work XSA wheels (need restoring, I've made a start..), Shift kit put through the 5 speed tiptronic auto, TV and menus/screens changed to english, Australian DTV tuner installed in rear. I've just had four new discs and new pads as well as all the fluids including the brake fluid replaced. I have all the receipts for the last 15 years and the import papers in a nice folder. Car looks great, goes like hell but fuel economy is not a thing lol.. pics next..
    • I ended up in this rut again lol, and used a shit ton of filler. One thing I can't understand is, even after using a big long block and going in long X pattern strokes, I always end up at bare metal again with no filler, and my repair started at one end of the door and now I've chased my tail to almost the other end of the door. I was thinking of hitting the panel with a hammer where it might be a high spot and making everything low then filling it, I did this on a small section on my other door by mistake and I think I fixed it lol. Is this a bad idea? The other thing is with guidecoat, whether it's the powder or spray, after I sand all the guide coat off, it doesn't reveal anything for me in terms of high spots and low spots and makes it especially hard when it's bare metal (at least in powdered form), am I doing something wrong here, or likely a high spot I keep going over and creating valleys? Lastly, stupid question but, is it possible that after sanding if I only sand over the filler area where I know to be a dent that it's impossible for me to dig into that dent? Unless there are other problems which I missed.  
×
×
  • Create New...