Jump to content
SAU Community

Recommended Posts

I read the thread. I think I understand. So I need to buy a resistor pack for the GTR injectors from Nissan, I live in Japan, rewire everything and it works?

The GTR injectors are top feed, the GTS-T are side feed, how are they going to fit?

Help

I read the thread. I think I understand. So I need to buy a resistor pack for the GTR injectors from Nissan, I live in Japan, rewire everything and it works?

The GTR injectors are top feed, the GTS-T are side feed, how are they going to fit?

Help

RB20 injectors are top feed

You don't NEED to buy a resistor pack from a GTR, you can just wire in the appropriate resistors into the loom.

Thanks everyone.

So I just buy the one resister and wire everything in like in the link on this page?

I will go with a bigger fuel pump then since I don't need bigger injectors yet.

  • 1 month later...

im getting some gtr injectors but ive been told they will work with no other mods & that i dont need a resistor pack?

i cant see how this is this possible, or am i wrong?

ok i just found this thread which sorta explains that you can run them without the resistor pack but it might fry my power fc!

i cant risk that...help :|

http://www.skylinesaustralia.com/forums/Gt...l=gtr+injectors

Edited by NWR31

i wouldn't advise driving it un-tuned after installation.

put it this way; driving it from my mechanics driveway onto the tow-truck, and then driving it off the tow-truck and into my garage fouled the plugs!

Edited by dmr

this pfc was tuned for gtr injectors/z32 which will be the same mods as me. i know it still wont be safe to drive on but should be in the ballpark, i also have a good wideband gauge installed to check afr's.

anyway im more worried about frying my fc if i install these gtr injectors.

cheers

btw my fc is actually a rb26/gtr fc wired to suit my rb20.

would that make it more compatible with the gtr injectors & much less likely to fry the fc??

ok ive done a lot of searching & it seems even with the rb26 fc i do need a resistor pack to run gtr squirters...

Edited by NWR31

yeah thats what ive just read, cant understand why he's saying i dont need em.

i might have to reconsider buying them cause i dont want to root around wiring in resistors & the resistor pack might be hard to find or expensive..

thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...