Jump to content
SAU Community

Recommended Posts

  • Replies 82
  • Created
  • Last Reply

Top Posters In This Topic

Install seat and seat belt and it can be driven.

But before it gets driven it will get some semis and bolt on flares and a bit more weight reduction and some tidying up.

Still deciding whether to leave the torsen diff in it for it's first outing or put my mech center in now.

Edited by BHDave

Excuse the n00b question Dave, but whats the diff (hehe) between the two diffs?

And was that dumhed's?

Ando - we can easily fix that - go get some cans pf spray paint :blush:

Do you see now why we said your car was too pretty to be a nugget?

yeah, it was dumheds.

the torsen is a really nice street diff, they are great when you have weight over both wheels and provide good drive (so no single spinning the inside like a shagged viscous) but once you unweight or lift the inside wheel it goes open as you apply throttle.

with my penchant for bouncing off kerbs i can see it not working for me too well.

Also dumhed had issues with it spinning up on med to fast sweepers so he installed the big rice wing to keep a bit of load over the arse end which helped. That didn't come with the car so it will have that problem if i don't change the diff.

Ha ha yeah i agree.. but i got sick of having a pig of a car with the old Cefiro... the blue nugget is a bitz of both... noice but trackable..

Nice purchase! That car is loud and quick.... Go get a Fully GT spec wing from Jjap LOL You know you wana!

tmb is waiting to see how the new light weight bonnet turns out.

If it's good i'm sure he will give you the contact details.

Both boot and bonnet require pins so no good for street cars....

Eventually it will get a turbo.

I already have the 3071 off the old car and i have a low km s15 engine that i picked up as a partial trade on some bits.

So there's a new rear housing, manifold, cams, springs, rocker arm stoppers, gate, and head gasket to get into it before install.

The car already has an s15 pfc installed so it's an easy swap.

short term is get some flares, get some new semis on my 17x9 +25 sterns, tidy it up a bit and drive it.

Not so short term is full re wire, more weight reduction, and some paint.

Engine is a long term one. So about 6 months or so depending on money :)

The r32 was scary. This thing will be in a different league once it gets a turbo. The previous owner has already got it into the 9's as it stands and i used to dive past it on the straights like it was standing still....

Do you see now why we said your car was too pretty to be a nugget?

yeah, it was dumheds.

the torsen is a really nice street diff, they are great when you have weight over both wheels and provide good drive (so no single spinning the inside like a shagged viscous) but once you unweight or lift the inside wheel it goes open as you apply throttle.

with my penchant for bouncing off kerbs i can see it not working for me too well.

Also dumhed had issues with it spinning up on med to fast sweepers so he installed the big rice wing to keep a bit of load over the arse end which helped. That didn't come with the car so it will have that problem if i don't change the diff.

My old GTR diff does that but you can drive around it. Just have to drive better. (I'm not saying I do - just that I can tell the difference between getting a corner right and getting it wrong.)

bah! I'd rather cover for my lack of ability by jamming a better diff in it at zero cost :D

Sound like you need to invest in a nismo clutch pack bob :O

That's the way. I would.

One day, that would be nice, in the meantime I just try to drive smoothly.




  • Similar Content

  • Latest Posts

    • Cheers. Skyline is back on the menu, can’t get rid of it. It’s like a child you don’t want, or herpes 
    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
×
×
  • Create New...