Jump to content
SAU Community

Recommended Posts

Hi There,

Finally i got the car. Full NISMO body kit. Brembo. No Stereo, but have ordered one on the way. Any one can shed some light on how to take apart the double DIN or the center console? After I took out the gear cover, I see 2 screws at the bottom of the 2 DIN. But After they are undone, the whole console just wouldn't bunch. Any idea?

post-53067-1217233540_thumb.jpg

post-53067-1217233554_thumb.jpg

post-53067-1217233697_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/229986-got-my-v35/
Share on other sites

Hi There,

Finally i got the car. Full NISMO body kit. Brembo. No Stereo, but have ordered one on the way. Any one can shed some light on how to take apart the double DIN or the center console? After I took out the gear cover, I see 2 screws at the bottom of the 2 DIN. But After they are undone, the whole console just wouldn't bunch. Any idea?

start on the left: remove passenger sill trim,remove passenger kick panel, remove visible screw on lower corner of glovebox,open glovebox,remove ALL screws,remove single screw on inside lower corner of glove box, remove visble screws on the pocket, remove pocket, remove gearstick cover , remove two screws. pull off ac display cover. remove screw.

not done yet.

remove 10mm bolt under hood release. pull that panel off. remove two screws that hold pocket in, remove pocket and undo cig lighter.

almost done.

grab radio assy and pull outward. the WHOLE thing comes out. disconnect EVERYTHING that is attached to it. take it out and set on table. remove 4 screws that hold the bracket in place. remove pocket. fit radio.

order a harness and antenna adpater from me and wire the whole lot up.

reassemble!

if this gets you I do this for a living and if you are brissy based I will do it for a fee.

Link to comment
https://www.sau.com.au/forums/topic/229986-got-my-v35/#findComment-4041595
Share on other sites

Thanks Chris,

That looked like a whole afternoon job, Damn. I'll try it this weekend, If fail, I'll contact you again. I'm living near caridale shopping center. I got an extra Immobilizer fitted with the car, It has a button to press after I have turn the ignition on, wait 4sec before I can start up. I'm thinking of getting rid of it, before I even start to get an extra spare key, since i got only 1 key. Maybe add in an extra Alarm/Immobiliser too.

Link to comment
https://www.sau.com.au/forums/topic/229986-got-my-v35/#findComment-4042599
Share on other sites

Hi Chris,

I got the car from a guy from gold coast under the company, MAD VEHICLE PTY LTD. I saw the car for sale in the net and he drove it down to brisbane for the viewing. The worst part was, I didn't even test drive the car when I bought it. He said he got no insurance for it yet as the car was not registered yet. I'm thinking of getting my HID done, but I'm a little confuse with my head lights unit. As you can see from the pics, My low beam is on the top (Can't see the bulb type), but my high beam is the bottom lamp on a H4? I thought H4 have high & low built in together? I have also a spot light switch on my steering column which didn't work, maybe i need spot light in the front bar.

Link to comment
https://www.sau.com.au/forums/topic/229986-got-my-v35/#findComment-4044890
Share on other sites

Hi Chris,

I got the car from a guy from gold coast under the company, MAD VEHICLE PTY LTD. I saw the car for sale in the net and he drove it down to brisbane for the viewing. The worst part was, I didn't even test drive the car when I bought it. He said he got no insurance for it yet as the car was not registered yet. I'm thinking of getting my HID done, but I'm a little confuse with my head lights unit. As you can see from the pics, My low beam is on the top (Can't see the bulb type), but my high beam is the bottom lamp on a H4? I thought H4 have high & low built in together? I have also a spot light switch on my steering column which didn't work, maybe i need spot light in the front bar.

The low beam is on top usd D2R HID.

The High beam is on bottom with H4.

The drive light is share H4 with high beam. (control by the switch on light handle).

Link to comment
https://www.sau.com.au/forums/topic/229986-got-my-v35/#findComment-4045628
Share on other sites

  • 2 weeks later...

I'll ask a few questions:

when you pulled the passenger dash loose did you undo the yellow plug? that is the passenger airbag feed. did you unplug anything yellow?

as for resetting the light. I can but I'll have to get a scan tool first. that will also tell me what it came up for in the first place.

Link to comment
https://www.sau.com.au/forums/topic/229986-got-my-v35/#findComment-4073263
Share on other sites

I think i did undo the one at the back of the glove box only. The bigger plug. So, when can you get the scan tool? About the TV recepetion, I manage to get some channel, but it's fuzzy in black and white. How can i get a better picture? Did you see a plug in for mic at the back of the system? It's seems that the other side can't hear me when i call them using the bluetooth function. I did find a mic in the box.

I'll ask a few questions:

when you pulled the passenger dash loose did you undo the yellow plug? that is the passenger airbag feed. did you unplug anything yellow?

as for resetting the light. I can but I'll have to get a scan tool first. that will also tell me what it came up for in the first place.

Edited by FlyingEL
Link to comment
https://www.sau.com.au/forums/topic/229986-got-my-v35/#findComment-4076864
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • Bunnings would have just handed you your money back on that one!
    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...