Jump to content
SAU Community

V-band Clamps

satanic

By satanic,
in General Maintenance

 Share

Recommended Posts

satanic Grand Master

satanic

Posted
Posted

Just a general question... where does one go to get a good quality v-band clamp and not one that looks like it's going to bend / snap when tightened up?

I don't mind spending a bit of money so even if it's completely overkill, throw it at me.

I recall someone on this forum once posting up a photo of a billet clamp of sorts (made for aircraft I think), was purple.

Thanks in advance

S

Link to comment
https://www.sau.com.au/forums/topic/230020-v-band-clamps/
Share on other sites
satanic Grand Master

satanic

Posted
  • Author
Posted

Thanks for the response...

Yeah they're the ones that were posted before, but now I see them again - they're not what i want. I am in need of some quality V-Band clamps. Do they make something similar but in V-Band format?

Might get a few of those Wiggins ones for elsewhere!

Thanks bud

Link to comment
https://www.sau.com.au/forums/topic/230020-v-band-clamps/#findComment-4042058
Share on other sites
Dahtone Racing Grand Master

Dahtone Racing

Posted
Posted
Wouldn't have thought a wiggins clamp would pull down hard enough to be used on a radiator hose. They use flanged pipes and orings, they don't use compression to seal they use the orings hence their flexibility?

I'm sure if they can hold intercooler pipes they can hold a radiator hose

cooling systems only get to ~1 bar

Yeah great - got quoted about $500 for a 4" Wiggins clamp kit today... that's ONE CLAMP... does anyone have the number for an oil tycoon in Dubai? My best friend just got fired...

told you they were dear as poison LOL

Link to comment
https://www.sau.com.au/forums/topic/230020-v-band-clamps/#findComment-4044814
Share on other sites
Dahtone Racing Grand Master

Dahtone Racing

Posted
Posted
Adel Wiggins Flexible Tube Connectors, known familiarly as Wiggins Clamps, provide an ideal method for connecting and sealing two tubes.

They are available in aluminum with a stainless two-finger latch, and are frequently used for vacuum lines, water lines, and turbo intake plumbing.

All are qualified to AS1650 and MIL-C-22263 specs., and are tested to greater than 125 psi. operating pressure, at temperatures up to 450° F depending mainly on the o-ring material.

Link to comment
https://www.sau.com.au/forums/topic/230020-v-band-clamps/#findComment-4046021
Share on other sites
Omurru Veteran

Omurru

Posted
Posted

Ok deleted the last post and will try again. You can't just buy a wiggins clamp and slam it on over your silicon joins/hoses, there not that type of clamp. They can only be used for metal piping as you need to weld on the ferrules. Yes I know you can use them for pretty much anything. Had a quick look around for some pics to explain what I mean.

post-14136-1217403245_thumb.jpg

post-14136-1217403250_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/230020-v-band-clamps/#findComment-4046190
Share on other sites
Beer Baron Grand Master

Beer Baron

Posted
Posted

same goes for V band clamps. they are only good to join to pieces of alloy or steel pipe since you need to weld the appropriate flanges to the 2 pipes so you can use the V band clamp on it.

V band kit:

VBC_C3_C35.jpg

another good example of V band clamps and flanges. they are good for IC piping, and exhaust if you have the time and money to install them. :)

wg44vbands.jpg

Link to comment
https://www.sau.com.au/forums/topic/230020-v-band-clamps/#findComment-4046217
Share on other sites
Omurru Veteran

Omurru

Posted
Posted
can these be used on radiator hoses and such??
wiggins clamps can

but they are dear as poison

Wouldn't have thought a wiggins clamp would pull down hard enough to be used on a radiator hose.
I'm sure if they can hold intercooler pipes they can hold a radiator hose

Just sounds to me like your saying they can be used on silicone radiator hoses....

Link to comment
https://www.sau.com.au/forums/topic/230020-v-band-clamps/#findComment-4046218
Share on other sites
  • 5 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
    • r32-25t
      R32 gtr transmission strength, billet plate

      By r32-25t · Posted

      Wouldn’t touch par if they gave it to me. You need to ask how much power you’re looking to make and then add about 50% to it because that’s what you’ll end up making  The factory box says no more at about 350kw or so, the upgraded synchro boxes won’t handle much over 500kw for long and at that point you’re looking at an auto or dog engagement manual,  once you’ve gone dog engagement you may as well go sequential, they cost a little bit more but it’s worth it  also while you’re at it you should upgrade the transfer case with 10 friction plates 
×
×
  • Create New...