Jump to content
SAU Community

Recommended Posts

My car is R33 S1, but then I need a rear garnish to replace the crack one.

I found an S2 garnish...but I wonder whether it is the same size as S1 or would it fit?

Personally I like the middle part between the two rear lights being flat smooth though.....instead of plastic black.

Or if it doesn't fit, has anyone try painting the black rear garnish with the same colour as your car?

Or do you think it is possible to get a sheet of stainless steel or whatever flat metal thing to cover that and spray it with paint?

any good idea?

else......I will just get a used S1 garnish...and consider putting it back.

Link to comment
https://www.sau.com.au/forums/topic/230576-r33-s1-s2-garnish/
Share on other sites

They are the same size.

Personally i like the colour-coded Series 2 garnishes. I want my SKYLINE letters to glow, so i've bought a S1 one, and going to mask letters, etc and paint it white.

OMG I forgot to say, it is sedan.....

  • 2 weeks later...
They are the same size.

Personally i like the colour-coded Series 2 garnishes. I want my SKYLINE letters to glow, so i've bought a S1 one, and going to mask letters, etc and paint it white.

How do you mask the letters. Any one here can help :whistling:

I got this quote from an old thread;

http://www.skylinesaustralia.com/forums/Mo...hl=rear+garnish

hence your rear garnish is clear , maybe paint it and leave the word skyline clear , and pop some LED's behind there for each letter or so , and run it off the connection of one of you lights . as you would when hooking up an electronic boost controller , that way the lights only turn on when you turn your parkers or headlights on.

I got a clear garnish and the question is how do you paint the rear garnish and keep the skyline word clear. That's a very hard thing to do. I can't even make the skyline word straight from masking tape. How does anyone do it? Please help here :D

I havent done mine yet, but i did my brake calipers with masking tape and a sharp knife. The garnish should be the same, because the letters are raised. mask the letters, and use a sharp stanley/surgical knife to trim masking tape.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
×
×
  • Create New...