Jump to content
SAU Community

Recommended Posts

hello all... simpole questiopn that has been bothering me for ages and ages!!!/..... where do i go in he s/e suburbs of melbourne to get the blue nice looking silcon joins for my cooler piping...and at that... where do i go to get those high pressure clips.. i think they are called makele clamps... the ones that you tighten a nut on the bolt apposed to the shitty python hose clamps...thankyou guys

Link to comment
https://www.sau.com.au/forums/topic/231164-silicon-joins/
Share on other sites

autobarn and super cheap stock the usual 2.5" and 3" but if you after 2.25" or 2.75" then you will need to check out some of places nismoid mentioned, i got my 2.75 from purple pig.

Edited by W0rp3D
Link to comment
https://www.sau.com.au/forums/topic/231164-silicon-joins/#findComment-4060087
Share on other sites

weld them up??? dude...then how do ya get the piping out when ya need to?? plus the silicon piping looks sick!!! the stuff is expensive as though... i guess everything like this is on these cars.. heheh.. cheers boys

Well obviously you dont weld them all up but i probably should of spelled that out hey :P

There is no reason why you cant weld up the bottom half of your piping which gets rid of 2 silicon joins and you can still take the piping off without a problem :P

Link to comment
https://www.sau.com.au/forums/topic/231164-silicon-joins/#findComment-4060346
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
×
×
  • Create New...