Jump to content
SAU Community

Need R32 Gtr Standard Ecu And Afm's Etc

NSN180

By NSN180,
in Wanted to Buy

 Share

Recommended Posts

NSN180 Enthusiast

NSN180

Posted
Posted

Hi just after a few bits and pieces

Standard r32 gtr acu

R32 gtr afm's

R32 gtr standard cat back exhaust including the cat, also interested in the standard front pipes as well

And the rear speaker covers for a 94model 180sx

located in melbourne In desperate need!

cheers dave

LotusGTR Veteran

LotusGTR

Posted
Posted (edited)

I also have an ECU. I'm in Melbourne. I also will have a bit of the exhaust you're looking for. PM me and we can sort it out.

Edited by LotusGTR
doo doo Proficient

doo doo

Posted
Posted
Hi just after a few bits and pieces

Standard r32 gtr acu

R32 gtr afm's

R32 gtr standard cat back exhaust including the cat, also interested in the standard front pipes as well

And the rear speaker covers for a 94model 180sx

located in melbourne In desperate need!

cheers dave

Hey got standard front pipes in bris if you're stuck

  • 2 weeks later...
gdzlar1 Proficient

gdzlar1

Posted
Posted

i got got gtr afms with hks pods and standard ecu if want mate u can give me a call n well work out a price everthing is in immaculate condition 0421500057 cheers steve

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • WMDC35
      Wheel Sizes & Offsets For Skylines

      By WMDC35 · Posted

      A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Duncan
      RB20DE NEO smallbox clutch.

      By Duncan · Posted

      Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...