Jump to content
SAU Community

Recommended Posts

my gtr has lost compression and is driving like a one legged camel....

i have plans for it to make around the 330AWKW...

so far i have gotten myself some wiesco forgies 87mm....

will i need rods for this power figure???

i have dash -7 turbos and fuel system and management

i was thinking these parts

acl race bearings

crank collar

oil restrictor

good pump

oil return from back of head

fresh head (reconditioned) stock cams with cam gears

metal head gasket

aftermarket rods

forged pistons

anymore suggestions ???

Link to comment
https://www.sau.com.au/forums/topic/232032-r32-gtr-offically-dead-rebuild-time/
Share on other sites

Rods - stock is fine

Just a set of pistons... get the crank checked also. If its far gone just get a R33 GTR crank and not worry about collars etc.

You'll only tell that once you get it looked at.

Otherwise good list of parts.

Dont really need oil return from the back of the head if the restrictors are done right, i dont have a drain :worship:

sweet as i was thinking a tomei sump baffle , what do u recon?

also i read somewhere on the forum that its better to use Nissan piston rings in the Rb blocks due to the beading in process... should i use these or use the ones hat come with the wiescos???

also head studs???

main studs???

Edited by den001

Dont really need it IMO. Some will say you do, ive seen club day circuit GTR's with your power run for a few years without.

So unless your out there ALL the time, 10 times a year or so, probably not needed. Certainly not for a streeter.

Not 100% on the rings, i couldnt imagine a RB block being different in terms of getting the ring setting.

ok, i have changed my ways abit, i have sold off the dash 7's and the managment today,also my rb30/26 pistons and rods, i have also sold my gt80 and now have a to4z

im going to use the parts off my other car onto this....

sofar i have

hks 272 10.2mm lift cams

hks springs to suit

bronze valve guides

1mm oversized ferrera valves

hypertune plenum

85mm tb

jun pump

custom sump

bare virgin block

virgin r33 crank

motec m8

obviously this will make a shitload more power than the quoted 330awkw, ive had a look at some of the dyno figures in the fi section, ive been to afew shops today and asked about a piston and rod combo for a RELIABLE 450awkw... everyone has different outlooks on different brands, one guy says this, the other says that....

i have come up with a combo which ive been told that will work very well, je pistons or mahle pistons and a set of manley turbo tuff rods???

will this be adequate for a reliable 450kw, or is it overkill???

any more combos yous know of with firsh hand experience???

cheers

denis

  • 4 weeks later...

i sold the gtr and am now concentrating on my rb s15, a build should cost u about 7000 to 9000 depending on where u go, the build i have atm is costing about 16,000 bvut is full house everything, in my 26, i also have a 30 which i will bolt my big turbo on and put a auto in later, the 26 will have a to4z and a 25 box, want to run consistent 9 second passes with this setup, the 30 even quicker

Edited by den001

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...