Jump to content
SAU Community

JOINT R31 Dyno Day !@! 28th Sep. CONFIRMATION NEEDED THIS MONTH


Recommended Posts

Sorry Guys,

I haven't been Able to post for a while, as i have had some troubles remembering my password :P

Well The Time is Drawing Nearer And We Need To Get Some Definate Numbers To Ensure That The Day Will Be Going Ahead.

If You Would Like To Send An E-Mail [email protected] With Dyno DAY in the Subject, And Then Confirm That You Will Be Present And What Car You Will Be Putting On The Dyno...

This Should Be A Good Day Providing That We Get The Numbers To Make The Day A Success.

Please Have E-Mails Confirmed By The End Of This Month.

Regards,

Ashley Neal.

www.r31skylineclub.com

[email protected]

http://www.r31skylineclub.com/forum...y;threadid=3977

Hope To Catchup Soon Paul.

. . .

Regards,

Ashley Neal

Edit.......OOps!!! Wrong Thread

It is on barring torrential rain . Gates open 8am. I believe it is $40 for 1/2 day $55 for full day. No special licence reqired, car and driver set up as for drags ie non flammable neck to wrist to ankle and helmet, fire extinguisher is advised but not reqired.

BUT be aware they will be monitering exhaust noise level,..... over 95Decibels and you won't be running until you quieten it down. Place should be easy to find ...follow highway into town watch for Morgan Park sign on the left. Still hav'nt found out if BP Ultimax or Shell Optimax is available in Warrick so last available is on Ipswich highway at Gailes for Shell just before the Logan Expressway joins on and BP 2or3 K's futher on.

15L of Toluene in a tank full would bring Premium at 96 octane safely up past 98oct

Hi There Guys,

I Have a Time Ready

9:00am Dyno Commence. - So I would have to say that it should be 8:30-8:45 Arrival @ All Star Performance @ their new Shop. In Zilmere Road Virginia -

Address 194 Zilmere Road.

Contact : Ashley Neal

[email protected]

0413-491-847

Steven Dyal

0419-767-498

I have So Far Recieved 17 People Confirmed To Come To Make This Possible we need to have 30+ people I'm still waiting on hearing back from the Z car club and Datsun Clubs.

So If you Would Like A Place Please email a confirmation so that you can secure a run for 20$.

This will give you a full read out of the car and how it is performing.

Regards,

Ashley Neal.

www.r31skylineclub.com

[email protected]

  • 3 weeks later...

I already have my name down for this one.

I just got my new clutch in, I was worried for a while there that I wouldnt get it in time for the dyno day as it had to come from sydney from japan I picked it up wednesday arvo and started fitting it 6:00pm I had the car running 1:05am Thursday morning, including new oil in the diff, gearbox and motor + Filter. Not too bad considering I fitted it all on my lonesome.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...