Jump to content
SAU Community

Recommended Posts

Hi,

Just noticed my 33 has a bit of a fuel leak after being able to smell it in a big way every time I filled up

after having a look underneath I can see that it is actually laking as I can see where it appears to have been fuel running down the tank and over all the rear suspension bits.

Question is, is it common for these tanks to crack at all? Im thinking highly unlikely although just wanted a bit of a heads up before i start pulling stuff apart. at this point im thinking its coming from the top screw cap that you open to get to the fuel pump.

Any ideas/experiences?

cheers

Link to comment
https://www.sau.com.au/forums/topic/233926-fuel-leak-r33/
Share on other sites

I'd check the rubber o ring out that the fuel pump is under, and easy say 20 minute fix.

Also check around the filler cap area, when they comply the cars they have to install an ADR approved cap, some compliance guys just cut and shut but don't reseal. Check if your cap etc will spin if you twist it? If it does its just sitting there and neads resealing. Use a product called Sikaflex and it will reseal the compliance cap to the original filler neck. Its a urethane based product, so have heaps of rags handy and clean up with WD40. Don't use it on your o ring etc because once its set, you'll never get it apart again.

Link to comment
https://www.sau.com.au/forums/topic/233926-fuel-leak-r33/#findComment-4100560
Share on other sites

Has anyone heard of fuel tanks cracking? thats my only stress at this point.. seals i can fix easy enough

Yeah, usually happens a) if a car has been off road and tank is slammed on roads of something b) as mentioned above if the car has been hit. c) older car

also I've heard of people drill holes in theirs by accident.

Link to comment
https://www.sau.com.au/forums/topic/233926-fuel-leak-r33/#findComment-4106875
Share on other sites

  • 1 month later...

Having the same problem. Checked the O-ring and sure enough that needed replacing. That got back the woosh sound when opening the tank, however the smell and leak remained. So I jacked up the car to check where it was leaking from (since the filler neck showed no signs of leaking) and it appears to be leaking from where the filler neck meets the tank. Any advice would be much appreciated.

Thanks, Josh

Link to comment
https://www.sau.com.au/forums/topic/233926-fuel-leak-r33/#findComment-4202439
Share on other sites

If its not structurally damaged, if it is still solid, I'd just use some tank sealer putty. You can get that at Repco or whatever, will work easy, just smear it on and push/work it in around the critical area. Its made for quick repairs on fuel tanks.

If its flexing and looks like it will get worse, its a tank out job. There are shops around that will weld a tank up, I 've done it before myself, you drain it, let it dry out, find a diesel motor and start it up, feed the exhaust fumes into the tank with a hose and while it is running, weld the tank up [mig is best, but oxy will work as well, arc is too much for the thin metal of a tank unless your a genius welder]. The exhaust fumes stop any big bang, they are carbon monoxide/dioxide plus other stuff and stop or supress any flame. A petrol engine will also work, but its not quite as safe. I've heard of guys using CO2 bottles as well.

An alternative to that is someone with a big soldering iron and solder it up. I've never seen fuel fumes ignite off a hot soldering iron. But soldered joints are not as strong as weld, but they can be pretty strong, many solder repairs have lasted years on fuel tanks and radiators.

A word of caution, its not for the novice [practice on something else] or the faint hearted, so if you can't weld don't try it yourself.

The last alternative is another tank, but who's to say it won't happen again.

Link to comment
https://www.sau.com.au/forums/topic/233926-fuel-leak-r33/#findComment-4202712
Share on other sites

84ULP is the part number a cpc fuel cap. i think they are about $20 from your local auto store.

replacing the cap reduced the smell of fuel on my car, but still *shhhhhhhhhhhh* on a hot day. fuel does evaporate at a very low temp so i dont worry about it too much, worst things is having highly compressed fumes in your car and getting a static spark when u are fueling up, so losing approx 20ml of fuel through a non tight cap isnt much of a waste/risk.

btw how many kms do u get out of a full tank?

Edited by philta
Link to comment
https://www.sau.com.au/forums/topic/233926-fuel-leak-r33/#findComment-4207211
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...