Jump to content
SAU Community

Recommended Posts

On hard accelleration ussually after going over a speed hump.

At 5000rpm hear a sound from the engine a bit like what you'd expect from a noisy error buzzer and the rpm gets stuck at 5000 rpm for a couple of seconds and no acceleration of car.

.

Has anyone experienced this and what do I need to do to fix it?

Link to comment
https://www.sau.com.au/forums/topic/23458-turbo-stall-help-needed/
Share on other sites

its not the auto gearbox getting stuck between a shift is it?

auto gearbox normally shifts around 5k rpm, it could be that its having trouble moving up to next gear, so it takes a small amount of time to move up.

Could be an electrics problem (altenator, battery or ecu) or perhaps the gearbox is on its way out?

Used to happen occasionally in the supra, gear shifts would take a few seconds, and during these few seconds the car would keep revving (car would lose acceleration too)

car sounds more like its grinding ERRRRRRRRRRR

completely different engine/exhaust note! Like I said before - an alarming ERROR BUZZER just slightly louder than normal when under full boost. It kind of reminds me of a sound like air trying to be blown so super hard/fast through a horn so that the noise goes away! blabblabblab at extremely high frequency.

This does not happen on a smooth road. Only when accelerating HARD just after the front wheels go up onto a big speed hump, going over speed humps which jolt the car.

Beyond me, sorry, im a simple man :D

it does sound like a gearbox issue though, do you still shift thru gears with your auto as if it is manual? (ie shift to '2' when approaching lights)

Maybe get a mechanic just to have a quick check over the car, just make sure nothing is loose?

no fully auto in power mode.

I'm starting to think that the speed hump may be causing the gear to change early.

Also I feel that it may be compressor surge on the turbo.

What I would like to find out is - if the exhaust pipe is not firmly mounted could it cause this sort of problem? My exhaust pipe could be bumping around a bit. Its 3" inc dump.

Also could brake issues such as air in lines or uneven disks cause this? I have ABS.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If you want to do the wiring, the GTT engine ecu has the same pinouts extra that the seperate TCM in the NA car has. You can literally grab the wires/pins that lead into the Seperate TCM and wire them into the corresponding pins in the GTT Engine ECU. You could then in theory Nistune it. I realised this when everyone put it in the too hard basket and I actually looked at the f**kin R34 manual. This is after I had previously had a seperate aftermarket TCM controller in my original N/A chassis car and a very built gearbox from a GTT, running a seperate Haltech engine ECU. I ran into this issue when I re-shelled the car into a GTT shell, so my aftermarket TCM was no longer plug and play, because the loom/modules were not present. I was pretty livid when realizing just how simple the original fix actually was. It sat for 3+ years at various workshops trying to find a solution. In practice none of this is a worthwhile idea for a lot of reasons, generally surrounding the shitness of the NA auto, the autos in general that come with skylines, and the NA engine and lack of gains. The gearbox is specced for the 2.5L N/A and barely at that level. If you have to pay anyone any money to do any of this, that is money spent on manualizing the car and it's not even close in terms of a comparison. Learning to drive manual is simpler than going through the pain of dealing with the N/A gearbox and he'll have fun to boot.
    • Semi-correction to my blanket statement that you can't bend rubber hoses. It seems that you can get most of a result, by doing as this guy does. I wouldn't promise that the bends will stay in the hose forever. I think if I found they wouldn't stay, I'd get a larger hose and cut some 90°s out to go over the bends I wanted to be in the smaller hose, as a reinforcement.
    • Just a heads up. Mine has just failed. When i turn the car on it just reboots everytime then the word "Android" shows up then goes to a black screen. I've aksed the company i got it from for some help but it's passed their 90 day return so they wont help. I have to swap back to my old system this weekend 😭
    • Does the car have to stay auto? If so, you might be looking at a ZF swap in future. 
×
×
  • Create New...