Jump to content
SAU Community

Recommended Posts

so we can count you in on Team Nerd hippy :D have a look at this http://development.e-clips.com.au/anton/sh...nterCircuit.pdf need to convert that into a signal redable thru RS232...

looking at the specs for the ECU looks like we can display engine temp and boost and all sorts of cool things!!!

and there aint no reason we can't make the application skinnable so people could change the visuals of the dials and graphs and colors and stuff as well, that would be pretty swish!!!

  • Replies 109
  • Created
  • Last Reply

Top Posters In This Topic

Hey guys, just a thought on the whole power input project

The standard battery in most 'lines is not the best when it comes to adding excess drain. Just chuck in a couple of amps and watch your headlights flicker with the bass if you want proof.

Can be fixed though, try running two batteries in parrallel, or just designate a battery for the X-box. The last thing you'd want to do is fry your x-box once its built in.

2c>

An x-box can't take nearly as much as a few amps. It's a mere low end PC. I think between 5 - 10 amps of 12 volt current. Anyway, how can a lack of current fry something like this? I was having a serious lack of current in my desktop and my soundcard and a hard disk stopped working, and my cd burner and dvd burner wouldn't eject anymore... It's working fine again now.

I suppose it all depends on how much shit you want to add..

Great idea, but i think you're getting a bit carried away with trying to hack apart your console to get it in there. There isn't a hell of a lot of room behind there - and it is really designed for stereos only. If you put your screen on a stalk swivel its probably going to be better, then you angle it whenever as well.

I'd just chuck it in the boot, run AV cables to your TV screen, and rip out the USB jacks and run them via cables along your floor trims and the like and mount them somewhere in the front. If you've got a nice large HDD is there really any point having the CD unit in the front either?

Are you going to stepdown via a simple DC->240v inverter or are you going to try and pull out the xbox PSU and run direct onto the board?

Xbox isn't *that* sensitive to heat and vibration.. as long as you pad it well I think it should be fine. Hooking a powerslide might cause you problems I have a feeling though :P Make sure its well secured.

oh I just thought i had better throw in something as well NEEEERRD! lol .. but great idea. Would like to check it out if you manage to get it all working nicely.

woah a bit of interest since i last looked.. Looks like power is finally sorted out (as above):

- Zantech 250W DC->DC PSU (company located in VIC)

- ATX -> XBox Converter from xbox-scene... (guy located in Aust. or will just build ourselves -> pretty simple)

Thanks for the info on the battery. I will probably eventually be running 2 amps and the xbox.. looks like a battery upgrade/additional is in order..

Running out of room in the R33 fast here.... :)

pedator.. yeah my ideas are similiar..

But I don't even see the need to run the USB upfront.. there are RF wireless xbox controllers available - these can control all of the media player functions without much hassle..

If I get really keen I might run an extrension upfront for a IR remote.. a bit more 'user friendly' - i doubt it :)

XBox will be in the boot - probably in a custom box with some nice foam padding and mounted vertically to save some room and to ease vibrations on the HDD a little -

Will probably run an indash lcd at the front - i dont really want to hack things up etc. - if i somehow aquire a lot of money itll be a dvd player as well :)

I dont think its really going to be all that difficult - a few little annoyances that i've thought of:

- Have to run wire from igniition to trigger the xbox to turn on when you turn on the car etc. - might be able to do this the same way as you do an amp..

- Probably run a big cap to smooth out the power - will this help alleviate the problems when the starter motor initialy draws all its power?

- Probably have to do something about batteries etc.

- Have to somehow found the money for all this.. :)

$$$ is my issue at the mo... going to offload my notebook i think for a bit of funding assistance!

definately easier to get it all in the boot, maybe just get a single blank din plate and mount the ports on that rather than hacking up the dash.... gotta admit, it would look nice tho :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...