Jump to content
SAU Community

Recommended Posts

nah gtst mate, cheers for reply.

I tried calling fibrevision all day but i guess theyre busy lol, either engaged or didnt answer :S

I'm calling him on Wednesday on his mobile I'll try and tell him your tryna call if you pm me ur details... and if I remember to tell him.

I'd give you his email.. but he just got a new comp and I think his emails are farking up.

I'm calling him on Wednesday on his mobile I'll try and tell him your tryna call if you pm me ur details... and if I remember to tell him.

I'd give you his email.. but he just got a new comp and I think his emails are farking up.

I may be heading down there today as well at about 4. I hope they've got a brochure of all the bodykits they can get in because I'm not really too sure on what I want to get yet :blink:

I may be heading down there today as well at about 4. I hope they've got a brochure of all the bodykits they can get in because I'm not really too sure on what I want to get yet :D

They have the Monkey Warehouse and some other brochures there, yep. :blink:

im gunna go past tomorrow and pop in, hopefully can find out if he does them and for how much :(

Can you do me a favor and ask him if he got a chance to read my email reply. (Brandon after the Origin kit for R34.)

His mobile seems to be always off. And not sure if his emails are fixed yet. :D

I'm pretty sure ours fits GTS, I will have to confirm though.

it probably would do but the gts and the gtr kits are actually slightly different, im not too keen on the gtr one unfortunately :) thanks for following that up though :P

  • 3 weeks later...
  • 10 months later...

Hello. Your skirts , front and rear bar, what's the cost and what are the moulds like - not to bad to fit ? Thanks Dave

With our current courier (Allied Express) it's $400. However you are welcome to use your own courier, we are always researching new couriers for cheaper rates too.
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...